catia 管路教程

nullTubing Design 管路设计Tubing Design 管路设计CATIA Training FoilsVersion 5 Release 13 2004Course Presentation课程介绍Course Presentation课程介绍Objectives of the course目标 In this course you will learn how the CATIA Tubing Design product is used to quickly and efficiently create an intelligent tubing layout. 智能化管路设计 Targeted audience Experienced CATIA V5 users 目标学员 有使用经验的CATIA用户 Prerequisites CATIA V5 Fundamentals 予要求：CATIA V5基础Table of Contents目录Table of Contents目录Introduction to Tubing Design Fundamentals p.4 Accessing the workbench模块介绍 p.5 User Interface: Tubing Design Icons界面介绍 p.6 Creating Line ID’s生成管线ID码 p.9 Routing a Run 生成管线 p.10 Modifying a Run修改管线 p.14 Implementing Turn Rules管路拐弯 p.19 Placing Parts on a Run 管路定义功能 p.22 Generating Reports 生成管路拐点坐标 p.24Accessing the workbench进入模块Accessing the workbench进入模块To access the Tubing Design Workbench …进入模块1. Select the Start Menu3. Click on Tubing Design2. Select Equipment & SystemsTubing Design Workbench icon选择Start菜单选择设备和系统选择管路设计模块图标User Interface: Tubing Design Icons (1/2)User Interface: Tubing Design Icons (1/2)Line ID: Select/Query, Create, Transfer, Rename, Delete, Merge, Import管路ID码编辑Route a Run生成管路Update Part, Flip Part Position, Edit Part Parameters刷新功能、参数Place Tubing Part插入接头Offset Route, Route from Spline, Route thru a pathway偏距管路等Connect/Disconnect Part/Run, Create an offset segment con.连接Manage grafic representation几何显示Manage flows流量管理Create weld assembly管路焊接Build Tubing Part新建功能Align Side, Align Center, Rotate to Align, Distribute, Align two Planes移动Rename ID重新命名ID Snap, Snap three points, Snap center of polygon, snap Surface捕捉User Interface: Tubing Design Icons (2/2)User Interface: Tubing Design Icons (2/2)AxisGrid Step坐标轴网格距离生成平面显示模式Routing a Run (1/4)生成管路Routing a Run (1/4)生成管路Place Offset Plane生成起始面 Select the Offset Plane Icon选择图标 Offset Planes can be placed at anytime during the creation of Runs.此图标可以在生成管路时随时使用Offset Plane图标Routing a Run (2/4)生成管路Routing a Run (2/4)生成管路 Select the Line ID选择管线ID码 Depending on what Line ID is choosen, CATIA lets you select a predefined Turn Radius. In this case is just one Turn Radius for the 3/8in diameter defined, which means that you won´t get a selection panel.根据选择的管线ID码，可以选择拐弯半径Routing a Run (3/4)生成管路Routing a Run (3/4)生成管路 Create the Run生成管路 Make sure that the Grid Step is set to 0.5 in. 确认步长为0.5inClick when the green arrow pops up.Stop when the value reaches 2in.Point-To-Point-ModeRoute a Run图标当绿箭头出现时点击鼠标当到达一定长度时停Routing a Run (4/4)生成管路Routing a Run (4/4)生成管路Create a Run from Point-To-Point点到点方式生成管路 Click the the next two connectors. The Run will be created.点击两个支座，生成管路Modifying a Run (1/5)修改管路Modifying a Run (1/5)修改管路 Modify the Run修改管路 A new Run shall be created and afterwards being modified.先生成后修改 Therefore you create a new Run using the orthogonal mode as shown in the picture.使用对角线方式生成管路 After that you will modify the Run.然后修改Route a RunOrthogonalCreate the Run生成管路对角线方式产生管路Modifying a Run (2/5)修改管路Modifying a Run (2/5)修改管路Manipulation Handles Modify the Run修改管路 Runs can be edited by right clicking and choosing Runxxx.object – Definition in the contextual menu. You will see the skeleton of the Run, that consists of Segments, Nodes and Manipulation Handles.在管路上右击鼠标选择Definition菜单，将显示管路骨架，包括分段、节点和操纵柄 Segments can be stretched by dragging the green vertexes at the end of each segment.其中的分段可以通过鼠标拖拉端点而改变长度SegmentNodeAlignment of the Run操纵柄节点分段管路导向Modifying a Run (3/5)修改管路Modifying a Run (3/5)修改管路 Modify the Run修改管路 Segments and Nodes can also be modified when the Run is in definition mode. You can modify Segments and Nodes by right clicking them.也可以在上下文菜单中选择定义来修改分段和节点Right click on segmentRight click on runModifying a Run (4/5)修改管路Modifying a Run (4/5)修改管路 Modifying the Run修改管路 Runs can also be modified by dragging the Planes at the end of each segment. The alignment of the planes depends on the alignment of the Compass! These Planes and the basic Plane of the Compass are always parallel! 也可以通过拖拉分段两端的平面改变管，此平面的朝向和罗盘的基准平面一致 During the modification of Runs the Offset Plane can be used to allow an exact placement.修改中可以使用等间距平面图标Offset PlaneDistance to Offset plane等间距平面命令间距Modifying a Run (5/5)修改管路Modifying a Run (5/5)修改管路 Transfering a Line ID转换管路ID码 Before you start creating a Run you must select the proper Line ID. It’s possible to change the Line ID afterwards by using the Transfer Line ID function.先选择ID码再生成 Select the Run, which Line ID has to be changed and the Transfer Line ID Icon. In the appearing dialog box you can select the new Line ID.管路生成后用转换图标改管特性 The appearing information dialog close with OK.确定Selected RunSelect the new Line ID here.Click OK to put it onto the Run.Transfer Line ID选择管路转换码图标选择新的ID码确定Implementing Turn Rules (1/3)拐弯Implementing Turn Rules (1/3)拐弯Design Table button activates the Rules options. Implement Turn Rules设置拐弯半径 You can adjust the Bend Radius for the Run using Rules from Design Rules catalog when starting the creation of a new Run.修改拐弯规则 When you are using a Line ID for the first time, the Design Table for the available Turn Rules appears automatically. Later you must click on the Design Table Button to access the Rules.生成管路对话框中使用拐弯规则，选择不同半径Available Bends for the selected Line ID.拐弯规则可选择的半径Implementing Turning Rules (2/3)拐弯Implementing Turning Rules (2/3)拐弯 Modify Turn Rules修改规则 You can modify the Turn Rule of a Run by right clicking it and then enter the Definition Dialog.右键上下文菜单选择Definition There you can enter a new Radius which effects the whole Run.输入半径，影响整个管路Definition dialogEnter the new Radius here.The new radius will effect all bends in the Run.定义对话框输入新半径整个管路的弯受影响Implementing Turning Rules (3/3)拐弯Implementing Turning Rules (3/3)拐弯Radius is now 0,5” (only for this bend).BEFOREAFTER Override Turning Rules超越规则 To apply a certain bend radius to one bend of the Run you must enter the Definition Dialog of the corresponding Node.修改单个弯需要使用节点的上下文定义菜单 Therefore enter the definition of the Run (right click – Runxxx.object – Definition) and then the definition of the node (right click the node – Definition).两次上下文菜单 In the appearing Node Definition you can enter a Bend Radius that only effects the selected Bend.Node Definiton DialogEnter the new radius here.Enter the definiton dialog of the node.如图所示节点定义对话框输入新半径值Placing Parts on a Run (1/2)插入接头Placing Parts on a Run (1/2)插入接头 Place Parts on a Run Select the Place Tubing Part Icon.选择图标 Check, that spec driven is turned off.关闭spec driven按钮 The Place Tubing Part Dialog appears. Click on the Browse Button (“…”).选择浏览 A class browser appears that lets you select a function.窗口中选择功能 Place Tubing PartBrowse图标浏览 Placing Parts on a Run (2/2)插入接头Placing Parts on a Run (2/2)插入接头BEFOREAFTER Place Parts on a Run插入接头 For the selected function you must specify a Part Type.对于选择的功能，选择一个类型 Click on the Run where you want to place the Part. At the end of Runs or Tubing parts a green vertex appears to show you, there is a connector. You can also use this connetors for placement.选择管路，出现一个绿色节点 If there are multiple parts aviable for the selected Part Type, then a Part Selection dialog box will be displayed. You may then select the appropriate part for your design.在Part Number中如果有多种，可以选择适合的 Generating Reports (1/2)生成弯管文件Generating Reports (1/2)生成弯管文件 Select a macro for the report宏命令 Select the Tubing LineID that shall be included in the report.选择管路 Select the Tools – Macro – Macros … function from the menu.菜单Tools-Macro-Macro… Select the PslTubingExtract.CATScript macro.选择宏命令文件，并运行Generating Reports (2/2)Generating Reports (2/2) The Report will be generated.产生弯管文件