The copyright belongs to InnoLux. Any unauthorized use is prohibited.
INNOLUX DISPLAY CORPORATION
LCD MODULE
SPECIFICATIONSPECIFICATIONSPECIFICATIONSPECIFICATION
Customer:
Model Name: AT070TN83 V.1
SPEC NO.: A070-83-TT-11
Date: 2007/05/11
Version: 01
□□□□Preliminary Specification
■■■■Final Specification
Option
■ AT070TN83 V.1 LCM
(TTL T-con with LED Driver)
For Customer ’s Acceptance
Approved by Comment
INNOLUX
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
InnoLux copyright 2004
All rights reserved,
Copying forbidden.
Record of Revision
Version Revise Date Page Content
Pre. Spec. 01 2006/12/05 Initial release.
02 2007/03/05 2
Add Note 1,2,3
Modify TTL connector model from “FH19S-40S-0.5SH”
to “FH19SC-40S-0.5SH”
3
Add Note 4
Add “ I: input, O: output, P: power”
6 Add “Backlight Driving Conditions”
16 Add Note 4
18 Modify TTL connector model in the Mechanical Drawing
Final-spec.01 2007/05/11 1
Modify backlight power consumption from “1.728W” to
“2.500W”.
Modify panel power consumption from “0.990W” to
“0.825W”.
5 Add the Max.value of VLED.
6
Modify the Typ.value of Icc from”300mA” to “250mA”
and Max.value from”350mA” to “300mA”.
Modify “IL” to ”ILED” and the value from “180mA” to
“500mA”.
Add Max.value of ILED.
Add Note 2,Note 3.
Modify Note 5.
12 Modify test condition 1.
14 Modify Note 6.
19 Add the weight of corrugated board.
INNOLUX
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
Contents
1. General Specifications............................................................................................................1
2. Pin Assignment.......................................................................................................................2
3. Operation Specifications.........................................................................................................5
3.1. Absolute Maximum Ratings..............................................................................................5
3.2. Typical Operation Conditions...........................................................................................6
3.3. Power Sequence .............................................................................................................7
3.4. Timing Characteristics .....................................................................................................8
3.4.1. Timing Conditions....................................................................................................8
3.4.2. Timing Diagram .....................................................................................................10
4. Optical Specifications............................................................................................................12
5. Reliability Test Items.............................................................................................................16
6. General Precautions.............................................................................................................17
6.1. Safety .............................................................................................................................17
6.2. Handling .........................................................................................................................17
6.3. Static Electricity ..............................................................................................................17
6.4. Storage...........................................................................................................................17
6.5. Cleaning .........................................................................................................................17
7. Mechanical Drawing .............................................................................................................18
8. Package Drawing .................................................................................................................19
8.1. Packaging Material Table ...............................................................................................19
8.2. Packaging Quantity ........................................................................................................19
8.3. Packaging Drawing ........................................................................................................20
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 1/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
1. General Specifications
No. Item Specification Remark
1 LCD size 7.0 inch(Diagonal)
2 Driver element a-Si TFT active matrix
3 Resolution 800X3(RGB)X480
4 Display mode Normally white, Transmissive
5 Dot pitch 0.0635(W)X0.1905(H) mm
6 Active area 152.4 (W)X91.44 (H) mm
7 Module size 165(W)X104(H)X5.5(D) mm Note 1
8 Surface treatment Anti-Glare
9 Color arrangement RGB-stripe
10 Interface Digital(TTL)
11
Backlight power
consumption
2.500W(Typ.) Note 3
12 Panel power consumption 0.825W(Typ.) Note 2
13 Weight 130g (Typ.)
Note 1: Refer to Mechanical Drawing.
Note 2: Including T-con Board power consumption.
Note 3: Including LED Driver power consumption.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 2/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
2. Pin Assignment
TFT LCD Panel Driving Section
TTL Connector is used for the module electronics interface. The recommended model is
FH19SC-40S-0.5SH manufactured by Hirose.
Pin
No.
Symbol I/O Function Remark
1 VLED P Power voltage for LED Driver
2 VLED P Power voltage for LED Driver
3 ADJ I Adjust the led brightness with PWM Pulse Note 1,2
4 GLED P Ground for LED circuit
5 GLED P Ground for LED circuit
6 VCC P Power voltage for digital circuit
7 VCC P Power voltage for digital circuit
8 MODE I DE or HV mode control Note 3
9 DE I Data enable
10 VS I Vsync signal input
11 HS I Hsync signal input
12 GND P Power ground
13 B5 I Blue data input (MSB)
14 B4 I Blue data input
15 B3 I Blue data input
16 GND P Power ground
17 B2 I Blue data input
18 B1 I Blue data input
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 3/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
19 B0 I Blue data input(LSB)
20 GND P Power ground
21 G5 I Green data input(MSB)
22 G4 I Green data input
23 G3 I Green data input
24 GND P Power ground
25 G2 I Green data input
26 G1 I Green data input
27 G0 I Green data input(LSB)
28 GND P Power ground
29 R5 I Red data input(MSB)
30 R4 I Red data input
31 R3 I Red data input
32 GND P Power ground
33 R2 I Red data input
34 R1 I Red data input
35 R0 I Red data input(LSB)
36 GND P Power ground
37 DCLK I Sample clock
38 GND P Power ground
39 L/R I Select left or right scanning direction Note 4
40 U/D I Select up or down scanning direction Note 4
I: input, O: output, P: power
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 4/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
Note1: ADJ adjust brightness to control Pin,Pulse duty the bigger the brighter.
Note 2: ADJ signal=0~3.3V;Operating frequency:100~300Hz.
Note 3: DE Mode: Mode=”H”, HS floating and VS floating.
HV Mode: Mode=”L” and DE floating.
Note 4: Selection of scanning mode
Setting of scan
control input
U/D L/R
Scanning direction
GND VCC Up to down, left to right
VCC GND Down to up, right to left
GND GND Up to down, right to left
VCC VCC Down to up, left to right
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 5/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
3. Operation Specifications
3.1. Absolute Maximum Ratings
Values
Item
Symbol
Min. Max.
Unit Remark
VCC -0.3 6.0 V
Power voltage
VLED - 5.5 V
Input signal voltage VI -0.3 6.3 V
Operation Temperature TOP -20 70 ℃
Storage Temperature TST -30 80 ℃
Note: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. A module should be used with any of the absolute maximum ratings
exceeded, the characteristics of the module may not be recovered, or in an
extreme condition, the module may be permanently destroyed.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 6/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
3.2. Typical Operation Conditions
Values
Item
Symbol
Min. Typ. Max.
Unit Remark
VCC 3.1 3.3 3.5 V Note 1
Power voltage
VLED 4.8 5.0 5.2 V Note 2
Icc - 250 300 mA
Current consumption
ILED - 500 550 mA Note 3
Input logic high voltage VIH 0.7VCC - VCC V
Input logic low voltage VIL 0 - 0.3VCC V
Note 4
LED life time - 20,000 - - Hr Note 5
Note 1: VCC setting should match the signals output voltage (refer to Note 4) of customer’s
system board.
Note 2: LED driving voltage.
Note 3: LED driving current.
Note 4: DCLK,DE, HS, VS, R0~ R5,,G0~ G5,B0~ B5.
Note 5: The “LED life time” is defined as the module brightness decrease to 50% original
brightness at Ta=25℃ and VLED=5.0V. The LED lifetime could be decreased if
operating VLED is larger than 5.0V.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 7/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
3.3. Power Sequence
Power Supply Vcc
Data Signal
t
1
B/L
t
2
t
3
t
1
t1 >>>> 50 mSec
t2 ≧≧≧≧ 200 mSec
t3 ≧≧≧≧ 200 mSec
Note: Data Signal includes DCLK, DE, HS, VS, R0~ R5, G0~ G5, B0~ B5.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 8/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
3.4. Timing Characteristics
3.4.1. Timing Conditions
SYNC mode Input signal characteristics ( 800 x 480 )
Values
Item Symbol
Min. Typ. Max.
Unit Remark
Clock Period tCLK 20.0 30.0 - ns
Clock Frequency fCLK - 33.3 50 MHz
Clock Low Level Width tWCL 8 - -
Clock High Level Width tWCH 8 - -
Clock Rise/Fall Time tCLKr, tCLKf - - 3
ns
HSYNC Period tHP - 928 - tCLK
HSYNC Pulse Width tHW - 48 - tCLK
HSYNC Back Porch tHBP - 40 - tCLK
HSYNC Width + Back Porch thw + tHBP 88 tCLK
Horizontal valid data width tHV 800 tCLK
HSYNC Front Porch tHFP tHP - tHW - tHBP - tHV tCLK
Horizontal Blank tHBK tHP - tHV tCLK
VSYNC Period tVP - 525 - tHP
VSYNC Pulse Width tVW - 3 - tHP
VSYNC Back Porch tVBP 29 tHP
Vertical valid data width tw 480 tHP
Vertical Front Porch tVFP tVP - tVW - tVBP - tw tHP
Vertical Blank tVBK tVP - tw tHP
Data Setup Time tDS 5 - - ns
Data Hold Time tDH 10 - - ns
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 9/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
DE mode Input signal characteristics ( 800 x 480 )
Values
Item Symbol
Min. Typ. Max.
Unit Remark
Period tCLK 20.0 30.0 - ns
Frequency fCLK - 33.3 50 MHz
Low Level Width tWCL 6 - -
High Level Width tWCH 6 - -
Rise/Fall Time tCLKr, tCLKf - - 3
ns
DCLK
Duty - 0.45 0.50 0.55 - tCLKL/ tCLK
Setup Time tDES 5 - -
Hold Time tDEH 10 - -
Rise/Fall Time tDEr, tDEf - - 16
ns
Horizontal Period tHP - 928 -
Horizontal Valid tHV 800
Horizontal Blank tHBK tHP - tHV
tCLK
Vertical Period tVP - 525 -
Vertical Valid tw 480
DE
Vertical Blank tVBK tVP - tw
tHP
Setup Time tDS 5 - -
Hold Time tDH 10 - - DATA
Rise/Fall Time tDr, tDf - - 3
ns
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 10/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
3.4.2. Timing Diagram
H s y n c
D E
t
H B K
t
H W
t
H B P
t
H P
t
H V
t
H F P
Input Vertical Timing
Input Horizontal Timing
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 11/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
DE(RGB Data)
t
DEr(
t
Dr)
t
DEf(
t
Df)
0.7VDD
0.3VDD
DE and RGB Input Timing
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 12/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
4. Optical Specifications
Values
Item Symbol Condition
Min. Typ. Max.
Unit Remark
θL Φ=180°(9 o’clock) 60 70 -
θR Φ=0°(3 o’clock) 60 70 -
θT Φ=90°(12 o’clock) 40 50 -
Viewing angle
(CR≥ 10)
θB Φ=270°(6 o’clock) 60 70 -
degree
Note 1
TON - 10 20 msec Note 3
Response time
TOFF - 15 30 msec Note 3
Contrast ratio CR 400 500 - - Note 4
WX 0.26 0.31 0.36 -
Color
chromaticity
WY 0.28 0.33 0.38 -
Note 2
Note 5
Note 6
Luminance L 250 300 - Cd/m2
Note 6
Luminance
uniformity
YU
Normal
θ=Φ=0°
70 75 - % Note 7
Test Conditions:
1. VCC=3.3V, VLED=5.0V.The ambient temperature is 25 .℃
2. The test systems refer to Note 2.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 13/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
Note 1: Definition of viewing angle range
Fig. 4-1 Definition of viewing angle
Note 2: Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD
screen. (Response time is measured by Photo detector TOPCON BM-7, other
items are measured by BM-5A/Field of view: 1° /Height: 500mm.)
Fig. 4-2 Optical measurement system setup
Normal line
θ=Φ=0°
Φ=90°
12 o’clock direction
Φ=270°
6 o’clock direction
Φ=0° Φ=180°
Active Area
θL
θT
θB
θR
Normal line
θ=Φ=0°
Photo detector
Φ=90°
12 o’clock direction
Φ=270°
6 o’clock direction
Φ=0° Φ=180°
Active Area
500mm
LCM
LCM
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 14/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval between
“White” state and “Black” state. Rise time (TON) is the time between photo detector
output intensity changed from 90% to 10%. And fall time (TOFF) is the time
between photo detector output intensity changed from 10% to 90%.
Fig. 4-3 Definition of response time
Note 4: Definition of contrast ratio
state Black"" the on LCD whenmeasured Luminance
state White"" the on LCD whenmeasured Luminance
(CR) ratio Contrast =
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: All input terminals LCD panel must be ground while measuring the center area of
the panel. The LED driving condition is VLED=5.0V.
100%
90%
10%
0%
P
h
o
to
d
e
te
c
to
r
o
u
tp
u
t
(R
e
la
ti
v
e
v
a
lu
e
)
TON TOFF
White (TFT OFF) Black (TFT ON) White (TFT OFF)
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 15/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
Note 7: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every
measuring point is placed at the center of each measuring area.
max
min
B
B
(Yu)Uniformity Luminance =
L-------Active area length W----- Active area width
W
W
/3
W
/3
W
/6 L/3L/3L/6
L
Fig. 4-4 Definition of measuring points
Bmax: The measured maximum luminance of all measurement position.
Bmin: The measured minimum luminance of all measurement position.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 16/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
5. Reliability Test Items
(Note3)
Item Test Conditions Remark
High Temperature Storage Ta = 80 240 hrs℃ Note 1
Low Temperature Storage Ta = -30 ℃ 240hrs Note 1
High Temperature Operation Ts = 70 240hrs℃ Note 2
Low Temperature Operation Ta =-20 ℃ 240hrs Note 1,Note 4
Operate at High Temperature
and Humidity
+40 , 90%RH max. ℃ 240 hrs Note 4
Thermal Shock
-30 /30 min ~ +℃ 80 /30 min for a total 100 ℃
cycles, Start with cold temperature and end
with high temperature.
Note 4
Vibration Test
Frequency range:10~55Hz
Stroke:1.5mm
Sweep:10Hz~55Hz~10Hz
2 hours for each direction of X. Y. Z.
(6 hours for total)
Mechanical Shock
100G 6ms,±X, ±Y, ±Z 3 times for each
direction
Package Vibration Test
Random Vibration :
0.015G*G/Hz from 5-200HZ, -6dB/Octave
from 200-500HZ
2 hours for each direction of X. Y. Z.
(6 hours for total)
Package Drop Test
Height:60 cm
1 corner, 3 edges, 6 surfaces
Electro Static Discharge ± 2KV, Human Body Mode, 100pF/1500Ω
Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panel’s surface.
Note 3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but doesn’t guarantee all the cosmetic specification.
Note 4: Before cosmetic and function test, the product must have enough recovery time,
at least 2 hours at room temperature.
INNOLUX SPEC NO.: A070-83-TT-11
PAGE: 17/20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
6. General Precautions
6.1. Safety
Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your
skin or clothes, wash it off immediately by using soap and water.
6.2. Handling
1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to
excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it carefully
to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module surface
with bare hands.
4. Keep a spac