打印机驱动说明
本文由linkailin贡献
pdf文档可能在WAP端浏览体验不佳。建议您优先选择TXT,或下载源文件到本机查看。
Zebra Universal Driver (ZUD)
陈利军
(Technical Support Specialist) 2006年2月16日
下载 ZUD
www.zebra.com/id/zebra/na/en/index/drivers_downloads/drivers.html
ZUD 支持的系统
安装、卸载 ZUD
Install&Uninstall ZUD.exe
ZUD 的参数
ZUD Setting.exe
Paper/Output
Paper Layout (图像方式旋转)
Landscape (倒立) Portrait (正立)
Paper Size (^PW ^LL)
Common label size Customize label size
Copies (^PQ)
Set the number of copies of each label to print.
Rotate 180 (^PO)
Set this to "On" will cause the label to be printed upside down.
Paper/Output
Mirror (^PM)
镜像打印,This is useful when printing on the back of transparent labels.
Negative (^LR)
反色打印,White areas will print as black and black as white.
Top Adjustment (^TA)
设置停纸位,Set the top adjustment offset necessary for the label to start
printing at the correct place on the label. This dimension is in dots and can be set
from -120 to +120.
自定义标签大小
在 “Paper Size Setup” 画面中 ,点击 “New” 按钮 为新建的标签创建一个名称 在
“unit of measurement”下拉窗口中选 择尺寸的单位. 在“Paper Sizes”中, 设置标签的
宽度 ( width )和长度(height),如果有 需要可以在“pager margin”中这是左边 距 Click "OK" to save your settings and select the custom label. 如果要删除一个纸张设置,
选择要删除 的标签的名称,点击"Delete".
Media Settings
Media Type (^MT) ? Thermal Transfer (使用碳带) ? Direct Thermal (不使用碳带) Media Tracking (^MN) ? Continuous (连续纸) ? Non Continuous(间隙纸) ? Non Continuous Mark sensing (黑标纸) ? Use Printer Setting (默认参数)
Document Options
Dispense Mode (^MM) ? Rewind the printed labels (回绕) ? Peel Off (剥离) ? Tear Off (默认参数,撕纸) ? Cut Label (切刀) ? Use printer settings (使用打印机设置) (Note:取决于打印机使用的选件)
Document Options
Smart Download ? 设为“On”后,改变处理图像的方式 Configuration ? Use Driver
Settings (使用驱动设置) ? Use Printer Settings (使用打印机设置)
Smart Download
用途:设定图形下载到打印机 的方法 解决的问题
标签文件很大时,丢失最后几行 的内容 ? 在标签上有阴影或水平的线条
原理:
当设置为“On”后,驱动程序把图 像中的白色区域不作为打印内 容,带来的结果就是产生的文件 会有很大程度上的缩小
Device Options (Speed Settings)
ZPL 命令: ^PR Print Speed ? 打印标签时的速度 Slew Speed (^PF) ? 当标签的末尾域没有内容时,打印机 在这段区域内走纸的速度 Back Feed Speed ? 打印机将标签回退到打印位置的速度
Device Options (Head Settings)
Print Darkness
ZPL 命令:这里是“,SD”,
不是“^MD”
Device Options (Printer Actions)
ZPL 命令: ^MF On Power up & On Head Close ? Do Nothing (不做任何动作) ? Do Calibration (校准纸张) ? Set Label length (设定纸张长度) ? Feed Label (进纸) ? Use printer setting (使用打印机设置)
User Commands
Start of Job
输入打印机指令,让打印机在开始打印一 个JOB之前,执行输入的命令
End of Job
输入打印机指令,让打印机在结束打印一 个JOB之后,执行输入的命令
Start of Page
输入打印机指令,让打印机在打印一个 Page之前,执行输入的命令
End of Page
输入打印机指令,让打印机在结束打印一 个Page之后,执行输入的命令
User Commands
Enter Commands 点击下拉菜单,选择 “Enter Commands„„”, 然后点击“„„” ,在 弹出窗口中,根据当前的打印机型 号输入ZPL、EPL、CPCL指令
~WC
Printer Firmware
Firmware
这个选项可以让驱动工作 在早期的 ZPL Firmware是 X.8和 X.9的打印机上使用 ? 不支持ZPL Firmware版本 低于 X.8 的打印机
Download Method
当选择 “Pre X.10” 时, 允许 设置下载图片是用ASCII mode 还是Binary mode. 这 个设置必须与打印机的设 置保持一致, 通常为 ASCII.
早期打印机驱动的选择
早期的打印机 105S/Se 140XiII 160S 170XiII 220XiII 90XiII 96XiII PA400 PT400
Stripe 300 Stripe 500 Z4000 Z6000 相似的驱动 105SL 140XiIII 220XiIII 170XiIII
220XiIII 90XiIII 96XiIII PA403 PT403 Stripe 400 Stripe 600 Z4M Z6M
Note: 对于低于 X.8版本的打印机,可以使用第三方的驱动(Seagull)
Image Options
Image Options ? Threshold ? Diffusion ? Floyd-Steinberg ? Halftone (半色调)
Image Adjustments
Image Adjustments 点击 “Intensity and Contrast” 打开 the “Image adjustments” 窗口, 可以调节图片的亮度和对比度
Commands – Passthrough Mode
Enable Passthrough Mode
介于分界字符中间的字符,被发送到打印 机是,字符不被转换保持原样,可以写一 段打印机指令
Commands – Bar Code Passthrough Mode
可以将两个或多个字符串 合并为一个条码数据
实际的打印效果
Commands – Line Substitution
Enable Line Substitution ZUD会使用^GB指令来了绘制线条或矩形,以此来产生条码
Printer Fonts Options
Internal Font
显示内置字体的名称
Horizontal Magnification
水平放大
Reversed
产生黑底白字
Rotation ? 0 Degrees ? 90 Degrees ? 180 Degrees ? 270 Degrees
Printer Fonts Options
New Internal Font ? 添加新的内置字体 Download Font ? 打开Font Download对话框,允许下载新的字体到打印机 Delete Font ? 从列表中删除选择的字体 ? 如果是下载的字体,会同时从列表和打印机中删除字体
使用新添加的内置字体
添加完新的内置字体后,可以在应 用软件(MS Word)中看到这个字体 Note:要先在应用软件中选择当前 的打印机为ZUD的打印机型号
下载字体
Important note: 下载的字体不会被显示为内置字体
使用下载的字体
Note: 要先在应用软件中选择当前的 打印机为ZUD的打印机型号 如果下载字体的时候,以 “Bitmap Font”形式下载,使用下 载字体时,字体大小要使用下载 时指定的字体大小 如果是使用“True Type”方式下 载,则字体大小可以在使用的自 定义
使用下载的字体
如果字体大小不匹配, 则会按照图像方式打印
使用“GS”字体
打印样张
Note:要先在应用软件中选择当前 的打印机为ZUD的打印机型号
Bar Code Options
Barcode Properties
显示条码的名称
Symbology
定义条码的属性:条码类 型、宽窄比、条码方向等
New
添加新的内置条码
Delete
从列表中删除条码
使用新添加的内置条码
添加完新的内置条码后,可以在应 用软件(MS Word)中看到这个条码 Note:要先在应用软件中选择当前 的打印机为ZUD的打印机型号
Advanced - Tools
Direct Command for printer
输入打印机的指令 ? 按 Send 按钮,直接把指令发送到 打印机.
Configuration
Print Configuration Label ? ZPL command: ~WC
Advanced - Tools
Memory Location
Select the memory to be use.
Print Object List
打印存储器中所有的文件 ? ZPL command: ^WDZ:*.*
Print Bar Code List
打印存储器中所有的条码 ? ZPL command: ^WDZ:*.BAR
Print Fonts List
打印存储器中所有的字体 ? ZPL command: ^WDZ:*.FNT
Advanced – Error Control
Error Control
“Enable”启动报错提示
Advanced – Command Format
Format
更改格式指令前缀 ? Note: The default value is 94. (^) ? ZPL Command: ~CC
Prefix
更改控制指令前缀. ? Note: The default value is 126. (~) ? ZPL command: ~CT
Delimiter
更改分隔符 ? Note: The default value is 44. (,) ? ZPL command: ~CD
Output printer code to a file
Output to a file.exe
打印机驱动克隆
备份、恢复打印机驱动的设置 将这个打印机的设置复制到另外一个电脑上
Driver Clone.exe
Question,