qq能上,ie浏览器不能用!网页打不开!（QQ can, IE browser can not use, web pages can not open!）

qq能上,ie浏览器不能用!网页打不开!（QQ can, IE browser can not use, web pages can not open!） qq能上,ie浏览器不能用!网页打不开!(QQ can, IE browser can not use, web pages can not open!) QQ can't use IE browser! Web page cannot be opened! - Possible reasons are: - First, the network settings This is because of the need to manually specify IP, gateway, DNS server networking, and the use of proxy server Internet access. Check your computer's network settings carefully. - - Two, DNS server issues - When IE cannot browse the web, the first attempt to use the IP address to access, if you have access, then it should be DNS problems, the problem may be caused by DNS for DNS error when networking or DNS server itself, then you can specify the DNS Service Manual (address is the address of the DNS server, you provide the local ISP can also be used in other places can normally use the DNS server address.) In the attributes of the network, (the address of the DNS server control panel - network and dial up connections - local connection - right property - TCP/IP protocol attribute using the following). Different ISP has different DNS addresses. Sometimes it's a router or NIC problem that can't be connected to ISP's DNS service. In this case, you can switch the router off for a while, or reset the router. - Another possibility is that the local DNS cache is having problems. In order to improve the website access speed, the system will automatically have access and access to the IP address of the site into the local DNS cache, once again visit this site, is no longer directly through the DNS server from the local cache to remove the DNS IP site visit. Therefore, if the local DNS cache problem occurs, it will cause the site to be inaccessible. Ipconfig /flushdns can be executed in run to rebuild the local DNS cache. - - Three, the IE browser itself - When the IE browser itself fails, it naturally affects browsing; or IE is maliciously modified and damaged, resulting in a failure to browse the web. Then you can try to use "Mount Huangshan IE repair experts to repair (suggestions into safe mode to repair), or re IE (such as IE encountered problems unable to reload, can refer to: a solution to reinstall IE) - - Four, the problem of network firewall - If the network firewall is set properly, if the security level is too high, accidentally put the IE into the block access list of firewall policy error, try to check the policy to reduce or directly off the firewall security level to see if it returned to normal. - Five, network protocol and network card driver problems IE is unable to browse. It may be caused by network protocol (especially TCP/IP protocol) or network card driver damage. You may try to renew network card driver and network protocol. - - Six, HOSTS file problems - HOSTS files are modified and also cause browsing to be abnormal. The solution is, of course, to empty the contents of the HOSTS file. - - Seven, the system file problems - When the file system associated with IE is replaced or damaged, will affect the normal use of IE, then use the SFC command to repair, WIN98 system can execute SFC in the "run", and then perform a scan; WIN2000/XP/2003 is in the "run" SFC /scannow attempt to repair. - When only IE and QQ can not browse the web, is often due to winsock.dll, wsock32.dll or wsock.vxd (VXD only exists in the WIN9X system) and other documents of damage or loss caused by Winsock, is an important part of the TCP/IP protocol, TCP/IP protocol to reload. But XP began to integrate the TCP/IP protocol, so it can not be uninstalled as easily as 98, and you can reset the TCP/IP protocol using the Netsh command to restore to the state of the initial installation of the operating system. Specific operations are as follows: - Click "start", enter "CMD" command in the run dialog box pops up, and then enter the command prompt window, "Netsh int IP reset c:resetlog.txt" command will enter the "resetlog.txt" file, which is used to record the Ri Zhiwen command execution results, the parameters must be specified here, the full path to the specified log file is "c:resetlog.txt". The result of executing this command is the same as deleting and reinstalling the TCP/IP protocol. - Tip: Netsh command is a command line tool written based on a script, you can use this command to configure and monitor the Windows system, it also provides interactive network shell interface, the use of the Netsh command format please refer to the help file (in the prompt input "netsh/?"). - The second solution is to repair the above documents, WIN9X re extracted files using SFC WIN2000/XP/2003 above, use the SFC /scannow command to repair the file, when using the SFC /scannow can not be repaired, can try online special repair tool to solve the problem of WinSockFix, in the online search and download. - - Eight, antivirus software real-time monitoring problem - This is not often seen, but sometimes really related to real-time monitoring, because now antivirus software real-time monitoring, have added to the content of the web monitoring. Give an example: KV2005 will cause IE unable to browse the web on the individual machine (many friends met), the specific performance is as long as the open web monitoring, a startup Internet about 20 minutes later, the IE will not browse the web, then if the "turn off KV2005 monitoring, everything back to normal; after completely reinstall KV2005 cannot solve. Although not installed KV2005 each machine will have this kind of problem, after all, each machine's system is different, installation procedures are not the same. But if IE is unable to browse the web, be sure to check the antivirus software. - - Nine, Application Management Services - Can only appear on the QQ can not open the web page, restart after the good. However, even restart, open 7 or 8 pages, and can not open a web page, only on the QQ. Sometimes, telecommunications often disable you by Application Management services. The specific reason is unknown. - Ten, infected with the virus caused by - This often occurs when IE is opened, and in the lower left corner of the IE screen prompts: "the page is being opened, but it does not respond for long time.". See the process in the task manager (enter method), The mouse on the taskbar, click the right button - Task Manager - process) to see how the CPU occupancy rate, if it is 100%, to be sure, is infected with the virus, then you simply want to run other programs. This is what we should look up the process of greedily occupied CPU resources. After finding the best record the name, and then click on the end, if not complete, to boot into safe mode to remove the stuff, but also into the registry, (method: start - run, enter the regedit Registry) in the dialog box. Edit - find, enter the program name, after finding the right mouse button to delete, and then search several times, often completely remove clean. -