打印机墨盒加墨方法

打印机墨盒加墨方法 Now on the market there are many types of cartridges after the original cartridge, refill ink to allow other users can continue to use, in accordance with the instructions from the original ink tank cartridge hole, vent holes in the ink tank, also can be in the original cartridge drill tank ink; but to the success of the ink tank. We must pay attention to the following matters: With the ink cartridge 1 operation notice: to ensure that the cartridge is filled is intact; rarely appear on the market at present the cartridge to use the damaged phenomenon, but the user in filling ink to the original cartridge, must learn to test the integrity of the cartridge; test method is specific, if in the bottom filling ink when found there is a lot of resistance. Note 2: try to use high quality original ink to fill, if users buy these fake ink, not only the use of the effect is not good, but also damage the inkjet printer. Therefore, when you buy ink, if you really want to buy ink jet printer's original ink, advise you to go to the corresponding brand printer repair center to buy, to ensure that it is true. If something goes wrong, the maintenance center can help you with it. With the ink cartridge operation note 3: before re filling ink, the original ink cartridges should be thoroughly cleaned, otherwise there are two kinds of ink mix and produce chemical reaction caused by failure of plug. Many users often use the printer cartridge cleaning with procedures for cleaning, in fact this is not only time-consuming operation, and cleaning is not clean; the right operation method for the first time in ink, unplug the piston three ink adding hole, find a syringe, pure water is injected into the cartridge, try not to let the the water overflows, then use the hand to hold the cartridge, and the ink adding hole upward, gently shake, so that the residual ink fully dissolved in the added water; if forced shaking is too large may make the liquid overflow inside, it should be promptly with paper towel or cloth. In order to avoid the diffusion into the circuit board caused by hardware failures, and then using the syringe to mixed liquid in the cartridge pumping clean, so repeated several times until you see the color of the liquid extracted by the printer was very shallow Comes with the cleaning cartridge program to clean. With the ink cartridge operation note 4: for filling ink cartridges, to a certain amount; many users feel for filling ink cartridges, the operation is complicated, in order to save, many people either do not give ink to ink tank, tank is full; and if the excess ink tank, ink cartridges will not only lead to appear ink leakage phenomenon in use, and leaking from the ink cartridge is likely to wet the components inside the printer, which may cause damage to the printer or printer circuit! If one is not careful to excess ink ink perfusion, must be timely with some soft paper or other light absorbing cotton to ink cartridge and nozzle, the excess ink absorption clean, but we do not use paper or other soft cloth and wipe back and printer nozzle. Ink box with ink operation note 5: as far as possible choose ink ink filling, so filling the effect will be better; Because the ink on the market has ink and ink, the ink is oily, and the ink is water quality. The original cartridge with ink for general ink, while the market is generally cheaper ink water ink, the ink is only 10 to 20 yuan, and fifty yuan to substitute ink; printing ink after filling, the contour is very clear. With the ink cartridge operation note 6: for filling ink cartridges, it is best not to immediately put back the cartridge cartridges, because many cartridges are included in the sponge pad absorbs ink, ink absorption speed and the sponge pad is relatively slow, so that the ink tank into the cartridge, not evenly sponge pad the absorption, so before the cartridge back into the cartridge, the cartridge is best to let the first standing for a few minutes, so that the ink slowly penetrated into every corner of the sponge pad, so as to ensure the final print quality. On the contrary, if we will immediately put it back after canned ink cartridges in the frame, then between the nozzle and the sponge pad will have air gap, and this gap will make the ink cartridge is difficult to smoothly flow out from the nozzle, so that the printing time will often appear fault phenomenon or a certain color printing line the lack of color. Note 7: ink cartridges should be prevented from exposing the cartridge to the air for long periods of time, even though there is a way to clean it. If the use of ink with high quality, we should be finished in the cartridge immediately after the ink cartridge, and ink on the printing ink immediately after; some of the original ink in the cartridge and the remaining will have some mixed change and clogging; if the printer does not use temporarily, can also be placed in the storage box of sprinkler nozzle special, the special rubber pad can cut off the air, keep long wetting the nozzle. With the ink cartridge operation note 8: if the print cartridges and the nozzle is integrated together, then to add ink cartridges, attention must be paid to the protection of the nozzle on the cartridge does not hurt, otherwise once the nozzle is blocked or damaged, the cartridge cannot be repeated use. In addition the cartridge in the frequent use process, the nozzle may be splashed back to the paper fiber plug, resulting output nozzle becomes worse, so regular cleaning of the nozzle is very necessary; cleaning nozzle, should try to use wet towel and cotton towel gently cleaning nozzle edge, and not hit the nozzle, then using inkjet printer control cleaning button on the panel to perform nozzle cleaning action, until the printing effect is clear so far. With the ink cartridge operation note 9: in inkjet printer ink cartridges plus, many primary users will select the lights in the ink for ink drained conditions; but for those who do not have the old inkjet printer ink light, can according to the printer prompts to transfer ink, but they did not ink inkjet cartridge indicator is mostly transparent, so we can be observed through the eyes of method to replace the ink, specifically the remaining amount of ink in the ink cartridge for the eye to determine what time to add ink, ink cartridge in 10% and usually on the remaining amount of filling; If you can't see the amount of ink left, you can only observe the effect of the last print. As long as you find a broken line in the print page, you should add ink to the cartridge.