海浮乐 ,来自德国
中国区代理商
高刚性液体静压系统
关于Hyprostatik
Hyprostatik,中文名:海浮乐,来自德国
具有25年液体静压产品的研发、生产经验
目前世界上最高刚性的液体静压产品,特别适合于重型、
超重型机床以及精密、超精密机床
出色性能≠高昂价格,以出色的成本优势,在机床业的
高端产品层面稳步普及
与其他从业者不同,我们能够提供以充分的理论计算为
基础的技术支持
核心产品——PM流量控制器(节流器)
工作原理
感应载荷的变化,以膜片反馈的方式,
即时地正比调节润滑油的流量,
使油膜的厚度趋于稳定,
从而实现非常高的系统刚度。
膜片反馈原理难以规模化生产,海浮乐是全球首家
系统示意图
核心产品——PM流量控制器(节流器)
强大的优势
PM控制器入口压力可达160 Bar,静压腔的布置更灵活、精简
超强优势:使溜板/滑枕上的狭小静压腔能够承受更大的负载
输出流量变化范围大,最大可达5L/min: 采用更少的油腔
膜片弹性变形范围为50微米左右,没有滑动部件: 动态响应迅
速,工作可靠,寿命长
油膜厚度不受环境温度的变化影响:简化机床设计
出色的性能
如上图所示,当静压腔压力从8.8 Bar上升到17.6 Bar时:
采用多头泵供油,油膜厚度变化为6μm;
采用海浮乐® 的PM流量控制器,其油膜厚度变化不到2μm,
刚度为多头泵方式的3倍以上。
理想无限刚度曲线
流量与油膜厚度的立方成正
比,在右图中,油膜厚度
不变的情况下,流量和压
力成正比。
不同节流器的流量曲线
压力变化时,流量随之变化
的实测曲线。
压力为8.8bar时
a 点:油膜厚度约为33μm
b 点:油膜厚度约为27μm
c点:油膜厚度约为21μm
压力为17.6bar时
油膜厚度均为20μm
四大类衍生产品
静压导轨与静压转台
提供:设计计算与 PM流量控制器
设计计算: 过去25年间,共为近1000个型号的机床实现了成套设计;
工作周期约为 5~9周(包含交流、计算、专适性设计等)
PM流量控制器: 年销量超过2万件;供货期约为 10个工作周
静压丝杠与静压轴承
2008年销量:350 根静压丝杠、150 只静压轴承
静压丝杠:40-225,最长达 5.5m,1200kN 轴向力, 最大速度
达 90m/min;供货期约为 3~7个月
静压主轴与液压站:
供货期约为3~6个月
全球独一无二的技术支持
目前液体静压应用的瓶颈,在于绝大多数相关从业者缺乏足够的理
论计算,这方面,海浮乐与众不同——
海浮乐拥有完善的演算系统,在设计静压系统时,每一项细节都有充分
详实的理论和数据计算作支持
迄今为止,共为近1000个型号的高端机床设计了液体静压系统,因此海
浮乐积累了许多关于机床结构设计方面的宝贵经验
当设计新机床的静压系统时,这些宝贵的经验积累将在与客户交流时起
到很重要的作用
如果,您使用液体静压的经验不足
没有关系,交给我们吧!
市场业绩
国内
在齐重数控、齐二机床、沈阳机床、上海机床、杭州机床等主
机厂出产的机床上配套应用
受邀参与数项机床科技重大专项
国外
客户众多,将另附专门文件介绍
著名的Kellenberger采用我们的静压产品,
形成领袖群伦的性能优势,并在各机床展会
设独立区域进行专门宣介(见右图)。
衍生产品Ⅰ——静压导轨
• 适用于较小切削力的高精机床
• no deformation by screws
• side stiffness and loadability
depends on the vertical power of
the V-pockets
• excellent for forming of the slide
with liquid guide plastic (SKC,
Moglish)
Hydrostatic V-flat guide ways
衍生产品Ⅰ——静压导轨
Prismatic hydrostatic guide ways
• stiffer than V-flat guide
ways
• better to produce by
grinding
• for higher side forces
衍生产品Ⅰ——静压导轨
Hydrostatic guide ways for linear motors
Suck down force of
the depressure
pockets is replaced
by the magnetic
attraction force
衍生产品Ⅰ——静压导轨
Hydrostatic guide ways with keeper rails
• for high loaded guide ways in
lathes, milling machines or
special grinding machines
• For vertical use
衍生产品Ⅱ——静压转台
国内最新应用
Φ5000,70rpm
table Ø2000/2500mm Ø2000/2500mm
bearing Ø1500mm Ø2400mm
application vertical lathe Gear grinder
speed 160 rpm 40 rpm
Runout <1µm <1µm
Radial force max.80 kN 60kN
Axial force max.265kN 700 kN
torque max. 130kNm 57 kNm
Axial stiffness >20 kN/µm >43 kN/µm
Radial stiffness >7kN/µm >10 kN/µm
Tilt stiffness >5000 kNm/mrad 20000 kNm/mrad
friction max 5,6kW max. 3 kW
Pump pressure 63 bar 50 bar
Oil type VG5 VG15
flow max.50 l/min max.23 l/min
table Ø2500mm
bearing Ø2100mm
application milling machine
speed 2 rpm
runout <1µm
Axial force max.750kN
using depressure
Torque load max. 80kNm
Axial stiffness >15 kN/µm
Torque stiffness >6000 kNm/mrad
friciton max 0,1kW
Pump pressure 50 bar
Oil type VG68
flow max.8 l/min
衍生产品Ⅲ——静压丝杠
the hydrostatic nut floats free of
contact on the hydrostatic pockets
free of backlash, very stiff and
extreme low friction
the nut has no friction at stand still
runs without noise and damps rotation
excellent
has no acceleration limit, short stroke
up to 10g
suitable for high axial forces max
1200kN
with rotating screw
max. total length 5m
screw 40-225mm
PM-flow controller included
衍生产品Ⅲ——静压丝杠
Application, where hydrostatic lead screw are used:
- X-axis of cam grinder and crank shaft grinder,
- to avoid wear at oscillating move
- Junker, Taccella, Studer, Schaudt, Doimak, …
- UP-machine and high precision cylindrical or flat grinder
– to keep position and move some nm
- IPT Aachen, LT-Ultra, Cranfield University, MTRC Florida, Okamoto,
Chevalier, Stöckel, Mitsui
- Oscillating axis of flat grinder
- to get wear free and low noise drive for high speed 60 m/min and
high acelleration e.g. 10 m/s²
- aba, z+b, Favretto, Mägerle, Blohm
- Die and mold milling machine
- to get much higher precision (+/-0,3µm) and surface quality (Ra
0,04µm)
– Kern, Keckeisen, Union, AMA Rottler, DS-Technology…
- Gear milling/grinding machines, press, pastic injectors, large lathes
- to move large weight with high precision and stiffness or
- to machine with high forces and finish with high precision
- to use high forces without wear
Pfauter, Forst, ..
衍生产品Ⅳ——静压主轴
Main advantage of hydrostatic spindles
spindle has no wear, so features keep same for long time
axial and radial roundness of run better 0,3µm, at optimized design 0,1 to
0,03µm – 5 to 10 times better than ball bearing spindles
balance quality typical G0,04, which is 10 times better than ball bearing
spindle in best shape.
friction heating is between the oil parts. Max. oil heating is 12°C and oil
leave spindle in 1 second. Position of spindle nose change by temperature
only about 4µm instead of 30µm of ball bearing spindles.
Hydrostatic spindles have very good damping
Hydrostatic bearings produce no vibration like ball bearings.
Hydrostatic spindles with PM-flow controllers have high stiffness
Adapted hydrostatic spindle at low speed can take very high forces
( large lathe spindle: radial force 1740 kN at front radial bearing
800mm, axial bearing +/-500kN with max. speed 40 rpm)
国内最新应用
(国家重大专项项目)
径/端跳:0.15μm
最高转速:5000rpm
功率:15kw
关于西技联
西技联
全称:西技联贸易(北京)
有限责任公司
西技联
致力于欧洲先进技术
和设备的引进与应用
代理品牌
Hyprostatik (德国)
Peron Speed (意大利)
Lubrix (德国)
Technosystems (意大利)
主力解决
主力解决方案
机床功能部件
液体静压——静压导轨、丝杠、转台、主轴
电主轴——高速、大扭矩、大功率
(多用于航空制造业)
机床润滑系统
绿色切削刀具润滑系统
高速主轴油气润滑系统
传动部件润滑系统
请联络我们
或访问我们的网站
www.EUROLINK.cn
电话:010-8496 5459
传真:010-8496 5460
Email:info@eurolink.cn