Brocade和Cisco光纤交换机级联配置

Brocade和Cisco光纤交换机级联配置 Brocade和Cisco光纤交换机级联配置 1.配置异构交换机平台协同工作模式 Cisco 9120配置过程 激活前8个端口 switch# config t Enter configuration commands, one per line.  End with CNTL/Z. switch(config)#interface fc1/1-8 switch(config-if)# no shutdown switch(config-if)# end 配置交换机协同工作模式 switch# config t Enter configuration commands, one per line.  End with CNTL/Z. switch(config)# vsan database switch(config-vsan-db)# vsan 1 interop switch(config-vsan-db)# end 配置domain ID switch# config t Enter configuration commands, one per line.  End with CNTL/Z. switch(config)# fcdomain domain 100 preferred vsan 1 switch(config)# end 激活VSAN switch# config t Enter configuration commands, one per line.  End with CNTL/Z. switch(config)# vsan database switch(config-vsan-db)# vsan 1 suspend switch(config-vsan-db)# no vsan 1 suspend switch(config-vsan-db)# end 察看修改之后的系统配置信息 switch# show running version 2.0(2b) vsan database   vsan 1 interop 1 fcdomain domain 100 preferred vsan 1 fcdomain fcid persistent vsan 1 boot kickstart bootflash:/m9100-s1ek9-kickstart-mz.2.0.2b.bin boot system bootflash:/m9100-s1ek9-mz.2.0.2b.bin kernel core target 0.0.0.0 kernel core limit 1 snmp-server user admin network-admin auth md5 0xeec64ba2afbe9b65e13b23882ac6ae05  priv 0xeec64ba2afbe9b65e13b23882ac6ae05 localizedkey username admin password 5 $1$V3smTQpb$MTvub69DkVBxdCt9BsEDB1  role network-admin callhome   switch-priority 7 snmp-server enable traps license interface mgmt0   ip address 192.168.70.139 255.255.255.0 interface fc1/1   no shutdown interface fc1/2   no shutdown interface fc1/3   no shutdown interface fc1/4   no shutdown interface fc1/5   no shutdown interface fc1/6   no shutdown interface fc1/7   no shutdown interface fc1/8   no shutdown interface fc1/9 interface fc1/10 interface fc1/11 interface fc1/12 interface fc1/13 interface fc1/14 interface fc1/15 interface fc1/16 interface fc1/17 interface fc1/18 interface fc1/19 interface fc1/20 switch# 察看端口连接状态信息 switch# show interface brief ------------------------------------------------------------------------------- Interface  Vsan   Admin  Admin   Status          FCOT   Oper  Oper   Port                   Mode   Trunk                          Mode  Speed  Channel                          Mode                                 (Gbps) ------------------------------------------------------------------------------- fc1/1      1      auto   on      up               swl    F       2    -- fc1/2      1      auto   on      up               swl    F       2    -- fc1/3      1      auto   on      up               swl    E       2    -- fc1/4      1      auto   on      notConnected     swl    --           -- fc1/5      1      FX     --      notConnected     swl    --           -- fc1/6      1      FX     --      notConnected     swl    --           -- fc1/7      1      FX     --      notConnected     swl    --           -- fc1/8      1      FX     --      notConnected     swl    --           -- fc1/9      1      FX     --      sfpAbsent        --     --           -- fc1/10     1      FX     --      sfpAbsent        --     --           -- fc1/11     1      FX     --      sfpAbsent        --     --           -- fc1/12     1      FX     --      sfpAbsent        --     --           -- fc1/13     1      FX     --      sfpAbsent        --     --           -- fc1/14     1      FX     --      sfpAbsent        --     --           -- fc1/15     1      FX     --      sfpAbsent        --     --           -- fc1/16     1      FX     --      sfpAbsent        --     --           -- fc1/18     1      FX     --      sfpAbsent        --     --           -- fc1/19     1      FX     --      sfpAbsent        --     --           -- fc1/20     1      FX     --      sfpAbsent        --     --           --   刀片中心光纤交换机模块配置 禁止交换机 brocadessm:USERID> switchdisable 修改Domain ID brocadessm:USERID> configure Configure...   Fabric parameters (yes, y, no, n): [no] yes     Domain: (1..239) [1] 99     R_A_TOV: (4000..120000) [10000]     E_D_TOV: (1000..5000) [2000]     WAN_TOV: (0..30000) [0]     MAX_HOPS: (7..19) [7]     Data field size: (256..2112) [2112]     Sequence Level Switching: (0..1) [0]     Disable Device Probing: (0..1) [0]     Suppress Class F Traffic: (0..1) [0]     Switch PID Format: (1..2) [1]     Per-frame Route Priority: (0..1) [0]     Long Distance Fabric: (0..1) [0]     BB credit: (1..27) [16]   Insistent Domain ID Mode (yes, y, no, n): [no]   Virtual Channel parameters (yes, y, no, n): [no]   Zoning Operation parameters (yes, y, no, n): [no]   RSCN Transmission Mode (yes, y, no, n): [no]   Arbitrated Loop parameters (yes, y, no, n): [no]   System services (yes, y, no, n): [no]   Portlog events enable (yes, y, no, n): [no]   ssl attributes (yes, y, no, n): [no]   http attributes (yes, y, no, n): [no]   snmp attributes (yes, y, no, n): [no]   rpcd attributes (yes, y, no, n): [no]   cfgload attributes (yes, y, no, n): [no]   webtools attributes (yes, y, no, n): [no] WARNING: The domain ID will be changed. The port level zoning may be affected brocadessm:USERID> msPlMgmtDeactivate Switch is in Offline state. 修改协同工作模式 brocadessm:USERID> interoper mode 1 The switch effective configuration will be lost when the operating mode is changed; do you want to continue? (yes, y, no, n): [no] y Interopmode is enabled Note: It is recommended that you reboot this switch for the new change to take effect. 重新引导交换机 brocadessm:USERID> fastboot  Broadcast message from root (pts/0) Tue Jun 13 10:07:45 2006... The system is going down for reboot NOW !! USERID Password: Please change your passwords now. Use Control-C to exit or press 'Enter' key to proceed. Password was not changed. Will prompt again at next login until password is changed. brocadessm:USERID> 激活交换机 brocadessm:USERID> switchenable 察看修改配置之后的交换机状态 brocadessm:USERID> switchshow switchName: brocadessm switchType: 22.0 switchState: Online   switchMode: Interop switchRole: Principal switchDomain: 99 switchId: fffc63 switchWwn: 10:00:00:05:1e:02:78:c6 zoning:         OFF switchBeacon: OFF Area Port Media Speed State ==============================   0   0   id    2G   No_Light    1   1   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:04   2   2   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:36   3   3   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:7a   4   4   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:b6   5   5   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:28   6   6   cu    2G   Online    F-Port  21:00:00:14:5e:24:aa:f6   7   7   cu    2G   Online    F-Port  21:00:00:14:5e:24:aa:f0   8   8   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:38   9   9   cu    2G   No_Light   10  10   cu    2G   No_Light   11  11   cu    2G   No_Light   12  12   cu    2G   No_Light   13  13   cu    2G   No_Light   14  14   cu    2G   No_Light   15  15   id    2G   Online    E-Port  20:01:00:0d:ec:06:b4:41 (downstream)     2.划分zone Cisco 9120划分zone   察看fabric连接设备port wwn 信息 switch# show fcns database vsan 1 VSAN 1: -------------------------------------------------------------------------- FCID        TYPE  PWWN                    (VENDOR)        FC4-TYPE:FEATURE -------------------------------------------------------------------------- 0x630100    N     21:00:00:14:5e:24:a9:04                 scsi-fcp 0x630200    N     21:00:00:14:5e:24:a9:36                 scsi-fcp 0x630300    N     21:00:00:14:5e:24:a9:7a                 scsi-fcp 0x630400    N     21:00:00:14:5e:24:a9:b6                 scsi-fcp 0x630500    N     21:00:00:14:5e:24:a9:28                 scsi-fcp 0x630600    N     21:00:00:14:5e:24:aa:f6                 scsi-fcp 0x630700    N     21:00:00:14:5e:24:aa:f0                 scsi-fcp 0x630800    N     21:00:00:14:5e:24:a9:38                 scsi-fcp 0x640000    N     20:07:00:a0:b8:21:19:9f (SymBios)       scsi-fcp:both 0x640100    N     20:06:00:a0:b8:21:19:9f (SymBios)       scsi-fcp:both Total number of entries = 10 创建zone 分别创建2个zone，前4个刀片服务器与DS4300 2个控制器组成的zone，第4到第8个刀片服务器与DS4300 2个控制器组成的zone。 switch# config t Enter configuration commands, one per line.  End with CNTL/Z. switch(config)# zone name blade_hs20_1-4 vsan 1 switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:04 switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:36 switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:7a switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:b6 switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:9f switch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:9f switch(config-zone)#exit  switch(config)# zone name blade_hs20_5-8 vsan 1 switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:28 switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f6 switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f0 switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:38 switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:9f switch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:9f  创建zoneset switch(config-zone)# zoneset name ds4300_blade vsan 1 switch(config-zoneset)# member Blade_Hs20_1-4 switch(config-zoneset)# member Blade_Hs20_5-8 switch(config-zoneset)# end 激活zoneset switch# config t Enter configuration commands, one per line.  End with CNTL/Z. switch(config)# zoneset activate name ds4300_blade vsan 1 Zoneset activation initiated. check zone status  察看激活的zone信息 switch# show zone active vsan 1 zone name blade_hs20_1-4 vsan 1 * fcid 0x630100 [pwwn 21:00:00:14:5e:24:a9:04] * fcid 0x630200 [pwwn 21:00:00:14:5e:24:a9:36] * fcid 0x630300 [pwwn 21:00:00:14:5e:24:a9:7a] * fcid 0x630400 [pwwn 21:00:00:14:5e:24:a9:b6] * fcid 0x640000 [pwwn 20:07:00:a0:b8:21:19:9f] * fcid 0x640100 [pwwn 20:06:00:a0:b8:21:19:9f] zone name blade_hs20_5-8 vsan 1 * fcid 0x630500 [pwwn 21:00:00:14:5e:24:a9:28] * fcid 0x630600 [pwwn 21:00:00:14:5e:24:aa:f6] * fcid 0x630700 [pwwn 21:00:00:14:5e:24:aa:f0] * fcid 0x630800 [pwwn 21:00:00:14:5e:24:a9:38] * fcid 0x640000 [pwwn 20:07:00:a0:b8:21:19:9f] * fcid 0x640100 [pwwn 20:06:00:a0:b8:21:19:9f]   保存系统配置信息 switch# copy running startup [########################################] 100% 刀片中心光纤交换机模块查看zone信息 brocadessm:USERID> cfgshow Defined configuration:  no configuration defined Effective configuration:  cfg: ds4300_blade   zone: blade_hs20_1-4    21:00:00:14:5e:24:a9:04   21:00:00:14:5e:24:a9:36   21:00:00:14:5e:24:a9:7a   21:00:00:14:5e:24:a9:b6   20:07:00:a0:b8:21:19:9f   20:06:00:a0:b8:21:19:9f  zone: blade_hs20_5-8    21:00:00:14:5e:24:a9:28   21:00:00:14:5e:24:aa:f6   21:00:00:14:5e:24:aa:f0   21:00:00:14:5e:24:a9:38   20:07:00:a0:b8:21:19:9f   20:06:00:a0:b8:21:19:9f 如上命令输出所示，Cisco 9120的zone 信息已经同步到刀片中心的交换机模块。 系统配置完成。