hp5200 维修
HP5200 tips for common error codes, printers, professional maintenance
Common error code, display information, information interpretation, dissolution method
13.1 paper jam or 13.2 paper jam printing paper is delayed or stopped in the feed section
1) make sure that the carton is properly installed; (2) determine the feeding part without obstructions; 3) check whether the PS402 and PS403 work properly; and replace the relevant sensors 1 when necessary
3.5 paper jam or 13.6 paper jam printing paper is delayed or stopped in the heating component section
1) determine the transfer roller and conveyor belt can work properly; 2) determine the feeding path without obstruction; 3) check whether the PS1307 work properly, and replace the sensor if necessary
13.10 paper jam printing paper in the suction area is delayed or stuck 1) examination paper feeder is part of the obstacle of paper feeding; 2) check feeder PS1701, PS1703 sensor is reset, if necessary, replace the relevant sensor
13.20 paper jam or 13.21 paper jam printing paper is stuck in the paper path or the printer cover is opened 1) check the paper conveying path, remove obstructions; 2) to check all the paper
parts are reset (including cover cover); 3) all pass examination paper on the path. Whether they need to replace the necessary reduction.
The 20 insuffient memory printer accepts too much data, beyond the memory range of the printer
1) press the [GO] button to continue printing (partial print content may be lost); 2) increase printer memory
21 page too comlex print content is too complex
1) press the [GO] button to continue printing (some of the print content may be lost); 2) set the PAGE PROTECT value to AUTO
22 EIO buffer overflow were sent to the designated EIO peripheral data too much press [GO] button to clear this information (data will be lost)
The 41.3 UNEXPECTED PAPER SIZE print paper does not match the model setting and sets the type of printing paper correctly
49.FF04 1. motor error
2. firmware version error (firmware version error on board)
50.* FUSER ERROR heating component error,
Its * values are expressed as follows:
1 heating temperature is on the low side
2 heating module preheating protection
3 heating temperature is on the high side
4 the supply voltage is unstable
5 heating component does not match the 1. turn off the power, 20 minutes after the boot; 2. re install heating components; the 3. switch off the power supply, remove the heating component, check the J1307-1 and J1307-2 as well as J1308-1 and J1308-2 is the same, such as the replacement of other components of thermal barrier,
51.*, PRINTER, ERROR laser scanning errors, * values are as follows: 1, laser detection error 2, laser error 1, restart; 2 re install the laser and connected cable; 3, replace the laser
52.* PRINTER ERROR laser scanning speed mismatch, * value is as follows: 1, scan start error, 2 scan, rotate error 1 restart, 2 re install laser and connected cable; 3, replace the laser
53.xy.zzPRINTER ERROR additional memory error,
The meaning of XYZ as follows: X=DIMM type 0=ROM1=RAMy= device position 1-3 wrong memory slot position error number zz= 0= does not support the installation of the 1= memory is not compatible with the range of 6= 5= memory installed 2= does not support the installation of memory type 3=RAM failed to detect 4= exceeds the maximum RAM exceeds the maximum ROM invalid DIMM 7=DIMM speed error signal 8=DIMM RAM parity error 9=ROM address
mapping error 10=DIMM 11=PDC XROM address conflict beyond the scope of 12= is unable to complete the 1 memory buffer to switch off the power supply, re installation of memory; 2 exchange memory insertion position; 3 replacement of false memory
55 PRINTER ERROR internal communication error 1. check the power position 2. replace the interface board 3. replace the DC control panel
56 * PRINTER ERROR * temporary printing error, said: 1. incorrect input or wrong additional device is connected 2. incorrect output 1. restart the printer configuration; 2. check printer; additional equipment connected to the 3. correction
57 PRINTER ERROR fan error 1. check whether the fan of the printer is properly connected and whether the obstruction is jammed or not. 2. replace the fan
58.3 memory error, 1. cartons, paper wheel, motor error on the right
2. 59.* PRINTER ERROR printer memory error motor error values are as follows: 0 * said motor error 1 motor starting motor error 2 error 1. restart the printer; 2. to determine the gear is connected to the normal operation of the motor; 3. to determine the cable connection was correctly inserted into the 4. replacement motor
62.* PRINTER ERROR printer memory error, * values expressed as follows: 0= 1-3 1. 1-3=DIMM internal memory slot re installation of memory; 2. exchange installation position; 3.
replacement insert memory 64 PRINTER ERROR receive data buffer error 1. restart the printer; 2. replacement interface board
66 xx.yyPRINTER ERROR external feeding errors, XY device number 2ndX= equipment types are as follows: a) 1stX= b) input device output device C) packaging / binding equipment yy= equipment error number 1. restart the printer; 2. check all cable connections; 3. re install external feeding equipment
79 PRINTER ERROR 1. printer error restart the printer to print the software used by the 2. detection; judging whether and printer matching; 3. replacement transmission cable and a power supply; 4. removal of DIMM5. if possible, use of parallel data transmission; 6. EIO removal equipment; 7. replacement card