Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
1
Features
Wide 3.6V to 18V Input Voltage Range
Output Adjustable from 1.222V to 16V
Maximum Duty Cycle 100%
Minimum Drop Out 0.6V
Fixed 380KHz Switching Frequency
2A Constant Output Current Capability
Internal Optimize Power MOSFET
High efficiency
Excellent line and load regulation
TTL shutdown capability
EN pin with hysteresis function
Built in thermal shutdown function
Built in current limit function
Built in output short protection function
Available in SOP8 package
Applications
LCD Monitor and LCD TV
Digital Photo Frame
Set-up Box
ADSL Modem
Telecom / Networking Equipment
General Description
The XL1410 is a 380KHz fixed frequency
PWM buck (step-down) DC/DC converter,
capable of driving a 2A load with high
efficiency, low ripple and excellent line and
load regulation. Requiring a minimum
number of external components, the regulator
is simple to use and include internal
frequency compensation and a
fixed-frequency oscillator.
The PWM control circuit is able to adjust the
duty ratio linearly from 0 to 100%. An enable
function, an over current protection function
is built inside. When short protection function
happens, the operation frequency will be
reduced from 380KHz to 80KHz. An internal
compensation block is built in to minimize
external component count.
Figure1. Package Type of XL1410
Administrator
附注
原厂代理商:
深圳市森利威尔电子有限公司
联系人:黄先生
手机:13760325070
QQ:2355368872
欢迎咨询,竭诚服务
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
2
Pin Configurations
XL1410
1
3
5
2
4 FB
NC
SW
VIN
GND
6
7
8
NC
EN
NC
Figure2. Pin Configuration of XL1410 (Top View)
Pin Number Pin Name Description
1,6,8 NC No Connected.
2 VIN
Supply Voltage Input Pin. XL1410 operates from a 3.6V to 18V
DC voltage. Bypass Vin to GND with a suitably large capacitor
to eliminate noise on the input.
3 SW Power Switch Output Pin (SW). Output is the switch node that supplies power to the output.
4 GND
Ground Pin. Care must be taken in layout. This pin should be
placed outside of the Schottky Diode to output capacitor ground
path to prevent switching current spikes from inducing voltage
noise into XL1410.
5 FB
Feedback Pin (FB). Through an external resistor divider
network, Feedback senses the output voltage and regulates it.
The feedback threshold voltage is 1.222V.
7 EN Enable Pin. Drive EN pin low to turn off the device, drive it high to turn it on. Floating is default high.
Function Block
Figure3. Function Block Diagram of XL1410
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
3
Typical Application Circuit
Figure4. XL1410 Typical Application Circuit
System Efficiency Curve
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
4
Ordering Information
Part Number Marking ID
Lead Free Lead Free
Packing Type
XL1410E1 XL1410E1 Tube
Package
Temperature
Range
XL1410TRE1 XL1410E1 Tape & Reel
XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant.
Absolute Maximum Ratings(Note1)
Parameter Symbol Value Unit
Input Voltage Vin -0.3 to 20 V
Feedback Pin Voltage VFB -0.3 to Vin V
EN Pin Voltage VEN -0.3 to Vin V
Output Switch Pin Voltage VOutput -0.3 to Vin V
Power Dissipation PD Internally limited mW
Thermal Resistance (SOP8)
(Junction to Ambient, No Heatsink, Free Air) RJA
100 ºC/W
Operating Junction Temperature TJ -40 to 125 ºC
Storage Temperature TSTG -65 to 150 ºC
Lead Temperature (Soldering, 10 sec) TLEAD 260 ºC
ESD (HBM) 2000 V
Note1: Stresses greater than those listed under Maximum Ratings may cause permanent damage
to the device. This is a stress rating only and functional operation of the device at these or any
other conditions above those indicated in the operation is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
5
XL1410 Electrical Characteristics
Ta = 25℃;unless otherwise specified.
Symbol Parameter Test Condition Min. Typ. Max. Unit
System parameters test circuit figure4
VFB
Feedback
Voltage
Vin = 7V to 18V, Vout=5V
Iload=0.2A to 2A
1.186 1.222 1.258 V
Efficiency ŋ Vin=12V ,Vout=5V Iout=2A - 89 - %
Electrical Characteristics (DC Parameters)
Vin = 12V, GND=0V, Vin & GND parallel connect a 220uf/50V capacitor; Iout=500mA, Ta =
25℃; the others floating unless otherwise specified.
Parameters Symbol Test Condition Min. Typ. Max. Unit
Input operation voltage Vin 3.6 18 V
Shutdown Supply Current ISTBY VEN=0V 60 200 uA
Quiescent Supply Current Iq
VEN =2V,
VFB =Vin
3 5 mA
Oscillator Frequency Fosc 323 380 437 Khz
Switch Current Limit IL VFB =0 4 A
EN Pin Threshold VEN
High (Regulator ON)
Low (Regulator OFF)
1.4
0.8
V
IH VEN =2V (ON) 1 15 uA EN Pin Input Leakage
Current IL VEN =0V (OFF) 1 15 uA
Max. Duty Cycle DMAX VFB=0V 100 %
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
6
Test Circuit and Layout guidelines
Figure5. Standard Test Circuits and Layout Guides
Select R1 to be approximately 2K, use a 1% resistor for best stability.
C1 and CFF are optional; in order to increase stability and reduce the input power line noise, CIN
and C1 must be placed near to VIN and GND;
For output voltages greater than approximately 10V, an additional capacitor CFF is required. The
compensation capacitor is typically between 100 pf and 33 nf, and is wired in parallel with the
output voltage setting resistor, R2. It provides additional stability for high output voltage, low
input-output voltages, and/or very low ESR output capacitors, such as solid tantalum capacitors.
CFF=1/(31*1000*R2); This capacitor type can be ceramic, plastic, silver mica, etc. (Because of
the unstable characteristics of ceramic capacitors made with Z5U material, they are not
recommended.)
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
7
Schottky Diode Selection Table
Current Surface
Mount
Through
Hole
VR (The same as system maximum input voltage)
20V 30V 40V 50V 60V
1A √ 1N5817 1N5818 1N5819
√ 1N5820 1N5821 1N5822
√ MBR320 MBR330 MBR340 MBR350 MBR360
√ SK32 SK33 SK34 SK35 SK36
√ 30WQ03 30WQ04 30WQ05
√ 31DQ03 31DQ04 31DQ05
3A
√ SR302 SR303 SR304 SR305 SR306
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
8
Typical System Application for 12V ~ 5V/2A Version
Figure6. XL1410 System Parameters Test Circuit (12V ~ 5V/2A)
Typical System Application for 12V ~ 3.3V/2A
Figure7. XL1410 System Parameters Test Circuit (12V ~ 3.3V/2A)
Datasheet
2A 380KHz 18V Buck DC to DC Converter XL1410
Rev 1.0 www.xlsemi.com
9
Package Information
SOP8 Package Mechanical Dimensions