ETSI EN 300 019-2-1 (V2.1.2)

ETSI EN 300 019-2-1 V2.1.2 (2000-09) European Standard (Telecommunications series) Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-1: Specification of environmental tests; Storage ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)2 Reference REN/EE-01024-2-1 Keywords Environment, equipment practice, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://www.etsi.org/tb/status/ If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. © European Telecommunications Standards Institute 2000. All rights reserved. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)3 Contents Intellectual Property Rights ................................................................................................................................4 Foreword.............................................................................................................................................................4 1 Scope ........................................................................................................................................................5 2 References ................................................................................................................................................5 3 Environmental test specifications.............................................................................................................6 3.1 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations...................................7 3.2 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations .....................................10 3.3 Specification T 1.3: Non-weatherprotected storage locations and T 1.3 E: Non-weatherprotected storage locations - extended..........................................................................................................................................13 4 Notes to tables ........................................................................................................................................18 4.1 General note .....................................................................................................................................................18 4.2 Notes to tables 1 to 7 ........................................................................................................................................18 Bibliography .....................................................................................................................................................20 History ..............................................................................................................................................................21 ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://www.etsi.org/ipr). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Environmental Engineering (EE). The present document is part 2, sub-part 1 of a multi-part EN covering the environmental conditions and environmental tests for telecommunications equipment, as identified below: Part 1: "Classification of environmental conditions; Storage"; Part 2: "Specification of environmental tests; Storage". Part 1 specifies different standardized environmental classes covering climatic and biological conditions, chemically and mechanically active substances and mechanical conditions during storage, transportation and in use. Part 2 specifies the recommended test severities and test methods for the different environmental classes. National transposition dates Date of adoption of this EN: 23 June 2000 Date of latest announcement of this EN (doa): 30 September 2000 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 March 2001 Date of withdrawal of any conflicting National Standard (dow): 31 March 2001 ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)5 1 Scope The present document specifies test severities and methods for verification of the required resistibility of equipment according to the relevant environmental class. The tests defined in Part 2-1 of this multi-part standard apply to storage of equipment covering the environmental conditions stated in ETS 300 019-1-1 [1]. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. • A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. [1] ETSI ETS 300 019-1-1: "Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-1: Classification of environmental conditions; Storage". [2] ETSI ETS 300 019-2-0: "Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-0: Specification of environmental tests; Introduction". [3] IEC 60068-2: "Environmental testing - Part 2: Tests". [4] IEC 60068-2-1: "Environmental testing - Part 2: Tests. Tests A: Cold". [5] IEC 60068-2-2: "Environmental testing - Part 2: Tests. Tests B: Dry heat". [6] IEC 60068-2-6: "Environmental testing - Part 2: Tests - Test Fc: Vibration (sinusoidal)". [7] IEC 60068-2-14: "Environmental testing - Part 2: Tests. Test N: Change of temperature". [8] IEC 60068-2-18: "Environmental testing - Part 2: Tests. Test R and guidance: Water". [9] IEC 60068-2-27: "Environmental testing. Part 2: Tests. Test Ea and guidance: Shock". [10] IEC 60068-2-30: "Environmental testing - Part 2: Tests. Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle)". [11] IEC 60068-2-56: "Environmental testing - Part 2: Tests. Test Cb: Damp heat, steady state, primarily for equipment". [12] IEC 60068-2-64: "Environmental testing - Part 2: Test methods - Test Fh: Vibration, broad-band random (digital control) and guidance". [13] IEC 60068-2-68: "Environmental testing - Part 2: Tests - Test L: Dust and sand". [14] IEC 60721-3-3: "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weatherprotected locations". ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)6 3 Environmental test specifications The detailed descriptions of the environmental conditions are given in clauses 4 and 5 of ETS 300 019-1-1 [1]. ETS 300 019-2-0 [2] forms a general overview of part 2 of the present document. If the equipment is normally stored in a packed state then it shall be tested in its packaging. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)7 3.1 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations Table 1: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - climatic tests Environmental parameter Environmental Class 1.1 Environmental test specification T1.1: Weatherprotected, partly temperature-controlled storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes low (°C) -5 -5 72 h IEC 60068-2-1 [4] Ab: Cold Air temperature high (°C) +45 +45 or +55 72 h IEC 60068-2-2 [5] Bb: Dry heat 2 change (°C/min) 0,5 none 3 low (%) 5 none 10 relative high (%) (°C) 95 93 +30 96 h IEC 60068-2-56 [11] Cb: Damp heat steady state 5 Humidity condensation yes none 6 absolute low (g/m3) 1 none 10 high (g/m3) 29 8 pressure low (kPa) 70 none 9 Air high (kPa) 106 none 9 speed (m/s) 1 none 10 rain intensity no Water low temperature no other sources no icing & frosting yes 10 Radiation solar (W/m2) 700 13 heat (W/m2) 600 13 ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)8 Table 1: Test specification T1.1: Weatherprotected, partly temperature-controlled storage locations - climatic tests Environmental parameter Environmental Class 1.1 Environmental test specification T1.1: Weatherprotected, partly temperature-controlled storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes sulphur SO2 (mg/m3) 0,3/1,0 none 14 H2S (mg/m3) 0,1/0,5 none 14 salts sea and road salt mist none 14 Chemically chlorine Cl2 (mg/m3) 0,1/0,3 none 14 active HCI (mg/m3) 0,1/0,5 none 14 substances nitrogen NOx (mg/m3) 0,5/1,0 none 14 NH3 (mg/m3) 1,0/3,0 none 14 hydrogen fluoride HF (mg/m3) 0,01/0,03 none 14 ozone O3 (mg/m3) 0,05/0,1 none 14 Mechanically dust sedimentation (mg/(m2h)) 1,5 none 15 active suspension (mg/m3) 0,2 none 15 substances sand (mg/m3) 30 none 15 Flora and micro organisms negligible Fauna rodents, insects negligible no = this condition does not occur in this class. NOTE: (n = number of note), see subclause 4.2. none = verification is required only in special cases. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)9 Table 2: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - mechanical tests Environmental parameter Environmental Class 1.1 Environmental test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Vibration sinusoidal velocity (mm/s) displacement (mm) acceleration (m/s2) frequency range (Hz) axes of vibration 1,5 5 2-9 9-200 5 2 5-62 62-200 3 3 x 5 sweep cycles IEC 60068-2-6 [6] Fc: Vibration (sinusoidal) 17 random ASD (m2/s3) (dB/oct) frequency range (Hz) axes of vibration 0,02 +12 -12 5-10 10-50 50-100 3 3 x 30 minutes IEC 60068-2-64 [12] Fh: Vibration, broad-band random (digital control) 18 Shocks shocks shock spectrum duration (ms) acceleration (m/s2) number of shocks directions of shocks Type L 22 40 none 19a Load static load (kPa) 5 none 20 no = this condition does not occur in this class. NOTE (n = number of note), see subclause 4.2. none = verification is required only in special cases. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)10 3.2 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations This specification applies to weatherprotected or partially weatherprotected storage locations having neither temperature nor humidity control. See tables 3 and 4. Table 3: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - climatic tests Environmental parameter Environmental Class 1.2 Environmental test specification T1.2: Weatherprotected, not temperature-controlled storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes low (°C) -25 -25 72 h IEC 60068-2-1 [4] Ab: Cold Air high (°C) +55 +55 or +70 72 h IEC 60068-2-2 [5] Bb: Dry heat 2 temperature change (°C/min) 0,5 none 3 low (%) 10 none 10 relative high (%) (°C) 100 93 +30 96 h IEC 60068-2-56 [11] Cb: Damp heat steady state 5 Humidity condensation (%) (°C) yes 90-100 +30 2 cycles IEC 60068-2-30 [10] Db: Damp heat cyclic Variant 1 7 absolute low (g/m3) 0,5 none 10 high (g/m3) 29 6 pressure low (kPa) 70 none 9 Air high (kPa) 106 none 9 speed (m/s) 30 none 10 rain intensity no Water low temperature no other sources dripping water 8 icing & frosting yes none 10 Radiation solar (W/m2) 1120 13 heat (W/m2) 600 13 ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)11 Table 3: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - climatic tests Environmental parameter Environmental Class 1.2 Environmental test specification T1.2: Weatherprotected not temperature-controlled storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes sulphur SO3 (mg/m3) 0,3/1,0 none 14 H2S (mg/m3) 0,1/0,5 none 14 salts sea and road salt mist none 14 Chemically chlorine Cl2 (mg/m3) 0,1/0,3 none 14 active HCl (mg/m3) 0,1/0,5 none 14 substances nitrogen NOx (mg/m3) 0,5/1,0 none 14 NH3 (mg/m3) 1,0/3,0 none 14 hydrogen fluoride HF (mg/m3) 0,01/0,03 none 14 ozone O3 (mg/m3) 0,05/0,1 none 14 Mechanically dust sedimentation (mg/(m2h)) 20 none 15 active suspension (mg/m3) 5,0 none 15 substances sand (mg/m3) 300 none 15 Flora and micro organisms mould, fungus, etc. none 16 Fauna rodents, insects rodents, etc. none 16 no = this condition does not occur in this class. NOTE (n = number of note), see subclause 4.2. none = verification is required only in special cases. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)12 Table 4: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - mechanical tests Environmental parameter Environmental Class 1.2 Environmental test specification T1.2: Weatherprotected not temperature-controlled storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Vibration sinusoidal velocity (mm/s) displacement (mm) acceleration (m/s2) frequency range (Hz) axes of vibration 1,5 5 2-9 9-200 5 2 5-62 62-200 3 3 x 5 sweep cycles IEC 60068-2-6 [6] Fc: Vibration (sinusoidal) 17 random ASD (m2/s3) (dB/oct) frequency range (Hz) axes of vibration 0,02 +12 -12 5-10 10-50 50-100 3 3 x 30 minutes IEC 60068-2-64 [12] Fh: Vibration, broad-band random (digital control) 18 Shocks shocks shock spectrum duration (ms) acceleration (m/s2) number of shocks directions of shocks Type L 22 40 none 19a Load static load (kPa) 5 none 20 no = this condition does not occur in this class. NOTE (n = number of note), see subclause 4.2. none = verification is required only in special cases. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)13 3.3 Specification T 1.3: Non-weatherprotected storage locations and T 1.3 E: Non-weatherprotected storage locations - extended This specification applies to storage locations which are not protected from direct weather influences. See tables 5 to 7. Table 5: Test specification T 1.3: Non-weatherprotected storage locations - climatic tests Environmental parameter Environmental Class 1.3 Environmental test specification T1.3: Non-weatherprotected, storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes low (°C) -33 -33 or -45 72 h IEC 60068-2-1 [4] Ab: Cold 1 Air high (°C) +40 +55 or +40 72 h IEC 60068-2-2 [5] Bb: Dry heat 2 temperature change (°C) (°C/min) 0,5 -10/+40 0,5 2 cycles t1 = 3 h IEC 60068-2-14 [7] Nb: Change of temperature 4 low (%) 15 none 10 relative high (%) (°C) 100 93 +30 21 d IEC 60068-2-56 [11] Cb: Damp heat steady state 5 Humidity condensation (%) (°C) yes 90-100 +30 6 cycles IEC 60068-2-30 [10] Db: Damp heat cyclic Variant 1 7 absolute low (g/m3) 0,26 none 10 high (g/m3) 25 8 pressure low (kPa) 70 none 9 Air high (kPa) 106 none 9 speed (m/s) 50 none 10 rain intensity (mm/min) (m3/min) (kPa) 6 0,01 90 3 min/m2 or 15 min IEC 60068-2-18 [8] Rb: Impacting water, Method 2.2 11 Water low temperature (°C) +5 11 other sources splashing water 12 icing & frosting yes none 10 Radiation solar (W/m2) 1120 13 heat (W/m2) negligible 13 ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)14 Table 5: Test specification T.1.3: Non-weatherprotected storage locations - climatic tests Environmental parameter Environmental Class 1.3 Environmental test specification T1.3: Non-weatherprotected, storage locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes sulphur SO2 (mg/m3) 0,3/1,0 none 14 H2S (mg/m3) 0,1/0,5 none 14 salts sea and road salt mist none 14 Chemically chlorine Cl2 (mg/m3) 0,1/0,3 none 14 active HCl (mg/m3) 0,1/0,5 none 14 substances nitrogen NOx (mg/m3) 0,5/1,0 none 14 NH3 (mg/m3) 1,0/3,0 none 14 hydrogen fluoride HF (mg/m3) 0,01/0,03 none 14 ozone O3 (mg/m3) 0,05/0,1 none 14 Mechanically dust sedimentation (mg/(m2h)) 20 none 15 active suspension (mg/m3) 5,0 none 15 substances sand (mg/m3) 300 none 15 Flora and micro organisms mould, fungus, etc. none 16 Fauna rodents, insects rodents, etc. none 16 no = this condition does not occur in this class. NOTE (n = number of note), see subclause 4.2. none = verification is required only in special cases. ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)15 Table 6: Test specification T 1.3 E: Non-weatherprotected storage locations - extended - climatic tests Environmental parameter Environmental Class 1.3E Environmental test specification T1.3E: Non-weatherprotected, storage locations - extended Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes low (°C) -45 -45 72 h IEC 60068-2-1 [4] Ab: Cold Air temperature high (°C) +45 +45 or +60 72 h IEC 60068-2-2 [5] Bb: Dry heat 2 change (°C) (°C/min) 0,5 -10/+40 0,5 2 cycles t1 = 3h IEC 60068-2-14 [7] Nb: Change of temperature 4 low (%) 8 none 10 relative high (%) (°C) 100 93 +30 21 d IEC 60068-2-56 [11] Cb: Damp heat steady state 5 Humidity condensation (%) (°C) yes 90-100 +40 6 cycles IEC 60068-2-30 [10] Db: Damp heat cyclic Variant 1 7 absolute low (g/m3) 0,03 none 10 high (g/m3) 30 8 pressure low (kPa) 70 none 9 Air high (kPa) 106 none 9 speed (m/s) 50 none 10 Water rain intensity (mm/min) (m3/min) (kPa) 15 0,01 90 6 min/m2 or 30 min IEC 60068-2-18 [8] Rb: Impacting water, Method 2.2 11 low temperature (°C) +5 11 other sources splashing water 12 icing & frosting yes none 10 Radiation solar (W/m2) 1120 13 heat (W/m2) negligible ETSI ETSI EN 300 019-2-1 V2.1.2 (2000-09)16 Table 6: Test specification T.1.3E: Non-weatherprotected storage locations - extended - climatic tests Environmental parameter Environmental Class 1.3E Environmental test specification T1.3E: Non-weatherprotected, storage locations - extended Type Parameter Detai