Application circuit examples of Si photodiode
1. Low noise light-sensitive preamplifier
Used in receivers for spatial light transmission and optical remote control.
A reverse bias is applied to the photodiode to improve frequency
response. This circuit outputs an amplified signal from the FET drain, but
signals can also be extracted from the source side for interface to the next
stage circuit with low input resistance.
KPDC0014ED
2. Low-level-light sensor head
The whole circuit is housed in a metallic shield box to eliminate external
EMI (electromagnetic interference). The photodiode window size should
be as small as possible. Use of an optical fiber to guide the signal light
into the shield box is also effective in collecting light. If dry batteries are
used and housed in the same shield box to supply power to the
operational amplifier, noise originating from the AC source can be
eliminated and the S/N ratio will be further improved.
KPDC0016ED
3. Light balance detection circuit
The output voltage Vo of this circuit is zero if the amount of light entering
the two photodiodes PD1 and PD2 is equal. The photoelectric sensitivity is
determined by the feedback resistance. By placing two diodes D in
reverse parallel with each other, Vo will be limited to about ±0.5 V
(maximum) in an unbalanced state, so that the region around a balanced
state can be detected with high sensitivity. Use of a quadrant photodiode
allows two-dimensional optical axis alignment.
KPDC0017EB
4. Luxmeter
This is an illuminometer using a visual-compensated photodiode S7686 and
an operational amplifier. A maximum of 5000 lx can be measured with a
voltmeter having a 5 V range. It is necessary to use an operational amplifier
which can operate from a single voltage supply with a low bias current.
A standard lamp should be used to calibrate the illuminometer. If no standard
lamp is available, an incandescent lamp of 100 W can be used for
approximate calibrations. To make calibrations, first select the 1 mV/lx range
in the figure at the right and short the wiper terminal of the 500 W variable
resistor VR and the output terminal of the operational amplifier. Adjust the
distance between the photodiode and the incandescent lamp so that the
voltmeter reads 0.38 V. At this point, illuminance on the S7686 photodiode
surface is about 100 lx. Then open the shorted terminals and adjust VR so
that the voltmeter reads 1.0 V. Calibration has now been completed. KPDC0018EC
-
+
ISC2 ISC1
PD2 PD1
Rf
D
D
2
3
76
4
-15 V
+15 V
VoA
10 k 10 µ
+15 V
1 k
0.1 µ
FET
0.1 µRS1 M
RL
PD
0.1 µ
1000 p
10 µ
Vo
++
PD : High-speed PIN photodiodes (S5052, S2506-02,
S5971, S5972, S5973, etc.)
RL : Determined by sensitivity and time constant of Ct of photodiode
RS : Determined by operation point of FET
FET: 2SK152, 2SK192A, 2SK362, etc.
PD Vo2
3
6
A1
-
+
3
2
6
+5 V
-5 V
0
Cf
Rf2
Rf1 S1
S2
10-TURN
POTENTIOMETER
10 µ
10 µ
+
+
A2
-
+
5
1
METALIC SHIELDED BOX
ISC
Bold lines should be within guarded layout or on teflon terminals.
A1 :AD549, etc. Rf : 10 GW Max.
A2 :OP07, etc. S : Low-leakage reed relay
Cf :10 to 100 pF, polystyrene capacitor PD: S1226/S1336/S2386 series, etc.
PD: S1226/S1336/S2386 series, etc.
A : LF356, etc.
D : ISS270A, etc.
Vo=Rf × (Isc2 - Isc1) (V) (Vo < ±0.5 V)
When the amount of light entering the two photodiodes is equal, the output
voltage Vo will be zero. In unbalanced state, Vo will be ±0.3 to 0.5 V. This
circuit can be used for light balance detection between two specific
wavelengths using optical filters.
IC : ICL7611, TLC271, etc.
PD: S7686 (3.8 µA/100 lx)
* Meter calibration potentiometer
100 p
1 k
1 k
PD
10 k
100 k
1 M
200 p 006 p
(9 V)
VOLTMETER
500VR *
7
6
8
4
3
2
1
0.1 (mV/lx)
1 (mV/lx)
10 (mV/lx)
IC
+
-
Isc V
1
5. Light sensor using high-speed operational amplifier (1)
This circuit uses a high-speed photodiode applied at a reverse voltage
and a current-to-voltage conversion operational amplifier. The time
response of the circuit greatly depends on the time constant of the
feedback resistance Rf and its parallel stray capacitance. To minimize the
effect of this time constant, two or more resistors are connected in series
as the feedback resistance to disperse the parallel stray capacitance. Use
of chip resistors as the feedback resistance will be effective in reducing
the stray capacitance.
KPDC0020EE
6. Light sensor using high-speed operational amplifier (2)
This light detection circuit uses a high-speed, current-feedback operational
amplifier, and allows direct connection to a coaxial cable. Because this circuit
performs signal amplification after current-to-voltage conversion by load
resistance RL, there will be no detrimental effects which result from a phase
shift in the amplifier.
As with the circuit 5., two or more resistors are used as the feedback
resistance to disperse parallel stray capacitance in the resistors. A ceramic
capacitor of 0.1 µF is connected to the power supply pin of the IC, and should
be grounded at a minimum distance. For bandwidths over 100 MHz, use of
chip resistors and capacitors is recommended to reduce the entire circuit size
and suppress the undesired effects of lead inductance of each component.
Performance can also be improved by using a ground plane structure in which
the entire copper foil surface on the PCB is used at the ground potential. KPDC0015ED
7. Light-to-logarithmic-voltage conversion circuit
The output voltage of this circuit is proportional to the logarithmic change
in the detected light level. A base-emitter junction of small signal
transistors or a diode between the gate-source of junction FETs can be
used as the log diode D1. IB is the current source that supplies the log
diode with a bias current. If IB is not present, the circuit will be unstable or
latched up when Isc by the incident light decreases to zero.
KPDC0021EA
8. High-speed light detector using PIN photodiode
This circuit uses no active components. Since no signal amplification is
performed, this circuit is mainly used for detection at relatively high
light levels. The impedance matching load resistance of 50 W can be
directly connected to the 50 W input terminal of an oscilloscope or other
measurement equipment.
High-speed photodiodes designed for the GHz range can be used with
this circuit. A chip capacitor should be used as the bypass capacitor C.
The photodiode leads and the conductors of the coaxial cable where high-
frequency current flows should be made as short as possible. Since the
signal current flows instantaneously to the load from the capacitor C in the
figure, it is necessary to select the capacitance that supplies the
corresponding electric charge.
In the figure at the right, if the cable is not terminated, the center
conductor is charged up at the power supply potential. If a high reverse
bias is used, sufficient caution must be taken not to exceed the maximum
rating of the input circuit of the measurement equipment, otherwise the
equipment may be damaged.
KPDC0022ED
Application circuit examples of Si photodiode
+
-
D1: Diode of low dark current and low series resistance
IB : Current source for setting circuit operation point, IB << Isc
R : 1 G to 10 GΩ
IO : D1 saturation current, 10-15 to 10-12 A
A : FET input Op-amp
Vo = -0.06 log + 1 ( ) [V]Isc + IBIO
.
.
+15 V
PD
-15 V
Vo
7
3
2
D1
A
4
6R
Isc
IB
10 µ +15 V
Rf
PD
-15 V
Vo
6
72
3 14
10 k
0.1 µ
A
+
+15 V
51 W
0.1 µ
+
-
0.1 µ
ISC
PD: High-speed PIN photodiodes
(S5052, S5971, S5972, S5973, etc.)
Rf : Two or more resistors are connected in series to eliminate parallel
capacitance.
A : AD743, LT1360, HA5160, etc.
10 k
10 µ
+5 V
0.1 µ
RL
PD
0.1 µ
Rf
Isc
R
-5 V
VO
42
3 7 6
A
+
-
+
0.1 µ
51 W
PD : High-speed PIN photodiodes
(S5052, S5971, S5972, S5973, etc.)
RL , R, Rf: Determined by recommended conditions of the operational amp
A : AD8001, etc.
Vo = Isc × RL × (1 + ) [V]Rf
R
A
+
-
PD
K
R
C
A
50 Ω COAXIAL
CABLE
SMA COAXIAL
CONNECTOR, ETC. SIGNAL
VOLTAGE
50 Ω
VR
-
+
BIAS
SUPPLY
PD: High-speed PIN photodiodes (S5052, S5971, S5972, S5973, etc.)
R : 10 kΩ, Voltage drop by photocurrent should be sufficiently smaller than VR.
C : 0.1 µF ceramic capacitor
The leads of PD and C from coaxial cable should be as short as possible.
(Chip components are recommended.)
2
9. CT scanner, X-ray monitor
In this application, scintillators are used to convert gamma-ray or X-ray
into UV or visible light which is detected by the photodiode coupled to the
scintillator. Reflecting material is used to wrap the scintillator to prevent
background light from entering the photodiode through the scintillator. At
the same time, the aluminum foil collects the generated light effectively
onto the photodiode.
Beta-ray can also be detected with the same circuit configuration.
However, it is necessary to use a light-shielding material which permits
efficient transmission of beta-ray.
KPDC0023EC
10. Gamma-ray, X-ray detector
When radiation is absorbed or scattered in a photodiode, a charge is
generated at that portion. This charge can be output to an external circuit
just as with detection of light. A1 used in this circuit is a charge amplifier
which converts a charge generated through the above process into a
voltage pulse. An operational amplifier with a large slew rate but small
bias current should be selected for A1. Use of a photodiode with smaller
active area offers a small junction capacitance and thus provides a large
output pulse, although at the expense of detection efficiency. As in the
case of 9., reflecting material or similar material should be used to shield
background light.
KPDC0024EB
11. Light absorption meter
This is a light absorption meter using a processor module (A in the figure)
which provides a logarithmic ratio of two current inputs. By measuring and
comparing the light intensity transmitting through a sample with two
photodiodes, a voltage output corresponding to light absorbance by the
sample can be obtained. To make measurements, the incident aperture
should first be adjusted so that the amount of light entering the two
photodiodes or photocurrent is equal. Next, the sample is placed on the
light path of one photodiode as shown in the figure. At this point, the
absorbance A by the sample can be directly read as A= -Vo (V) on the
voltmeter. For example, when a sample with an absorbance of 1
(transmittance 10 %) is detected, the output voltage will be -1 V. If a filter
is interposed as shown in the figure, the absorbance of specific light
spectrum or monochromatic light can be measured. KPDC0025EC
12. Total emission measurement of LED
This circuit is used to measure the amount of light emitted from an LED.
Since the emitting spectral width of LEDs is usually as narrow as about 50
nm, the amount of the LED emission can be calculated from the
photodiode radiant sensitivity at a peak emission wavelength of the LED.
In the figure at the right, the inner surface of the reflector block B is mirror-
processed so that it reflects the light emitted from the side of the LED
towards the photodiode. Therefore, the total amount of the LED emission
can be detected by the photodiode.
KPDC0026EA
Application circuit examples of Si photodiode
IF
LED Po
B
PD A
Isc
A : Ammeter, 1 to 10 mA
PD: S2387-1010R
B : Aluminum block, inner metal plating
Po : Total emission Po = Isc/S [W]
Refer to the spectral response chart for the photo sensitivity S of the
photodiode.
Example: S=0.58 A/W (λ=930 nm).
.
+15 V
Rf
PD
-15 V
Vo
3
6
10 p
0.1 µ
0.1 µA
+
-
4
2 7
SCINTILLATOR
X-RAY ISC
PD with scintillator : S8559, S8193, etc.
Rf : 10 M to 100 MΩ
A : FET operational amp
Scintillator : CsI (Tl), ceramic scintillator, etc.
PD : S3590 series, etc.
A1, A2: LF442
eo : Several mV to tens of mV for cobalt 60
+15 V
-15 V
9
A
+
-
100 p
PD
Vo
3
7
6
10
14
1
Isc1
Isc2
(SAMPLE)
FILTER
A : Analog Devices 755N/P, etc.
PD: S5870, etc.
Vo : Vo=log (Isc1/Isc2) [V]
Absorbance A by the sample can be read as A = -Vo (V) when Isc1 is
equal to Isc2 without the sample.
PD
ALMINIUM
FOIL CAP, etc.
+15 V
-15 V
8
5
6
A2
10 µ
+
-
0.1 µ
A1
+
-
7
100 k
10 k
100 p
eo
+24 V
10 k
3
2
2 p
10 M
A
K
+
4
3
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions.
Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2008 Hamamatsu Photonics K.K.
Cat. No. KPD1043E06
Jan. 2008 DN
13. Light integration circuit
This circuit is used to measure the integrated power or average power of a
light pulse train with an erratic pulse height, cycle and width. The
integrator A in the figure accumulates photocurrent generated by each
light pulse in the integration capacitance C. By measuring the output
voltage Vo immediately before reset, the average output current Isc can
be obtained from the integration time t and the capacitance C. A low
dielectric absorption type capacitor should be used as the capacitance C
to eliminate reset errors. The switch S is a C-MOS analog switch.
KPDC0027EA
14. Light-to-frequency conversion circuit
Making use of a C-MOS timer IC, this circuit generates pulses at a frequency
proportional to the amount of light. The capacitance C is charged with a constant
current Isc generated from the photodiode. When the potential of C increases
and reaches 2/3 of the supply voltage, the timer IC allows C to begin discharging
and its potential lowers. This discharge will stop when the potential of C lowers
to 1/3 of the supply voltage. For the calculation in the figure, the output pulse low
duration is ignored as it is very short. The duration is C × 100 kW.
While repeating the above process, the timer IC generates square wave pulses
whose frequency is proportional to the amount of detected light. Since the
reference voltage is created by dividing the supply voltage in the IC, the output
frequency varies with the supply voltage.
A bipolar timer IC (type 555) cannot be used because its terminal current is
usually larger than Isc. KPDC0028EA
15. Light-to-frequency Conversion Circuit Using PUT (Refer to JPN PAT. No. 1975639)
This circuit converts light into a pulse train at a frequency proportional to the
amount of light. A major difference from the circuit 14 is that the pulse oscillation
stops if the amount of light exceeds a certain threshold level. Light-to-frequency
conversion is nearly proportional in the specified range and the current
consumption is small.
An approximate oscillation frequency obtained with this circuit can be calculated
by the equation shown in the figure. When using constants shown in the figure,
this circuit operates in the range from about 1 lx to 200 lx, with a light-to-
frequency conversion ratio of 1.4 Hz/lx. The current consumption is approximately
10 µA.
The upper and lower limits of light level are determined by the valley and peak
currents of the PUT with respect to the combined gate resistance. The gate
resistance should be selected so that the photodiode current is in this range. KPDC0029EB
Application circuit examples of Si photodiode
+
-
Reset input: Use TTL “L” to reset.
A : LF356, etc.
S : CMOS 4066
PD: S1226/S1336/S2386 series, etc.
C : Polycarbonate capacitor
VO = Isc × t × [V]1
C
+15 V
PD
-15 V
VO
4
6
10 k
A
1 k
+15 V
3
2 7
14
2 S 1
1 k
C
13
7
RESET INPUT
VO
0 RESET
Isc
t
Isc
PD: S1087
IC : µPD5555 (C-MOS timer IC)
f = = × [Hz]
e.g. f=80 Hz at 100 lx when C=0.001 µF
1
t
3
Vcc
Isc
C
.
.
4
6 3
2
7
+7 to 15 V
Vo
78L05
0.1 µ
Vcc=+5 V
Isc
PD
100 k
C
0.01 µ
1 5
IC
t
Vo
8
Operational amplifiers used in these circuit examples will differ in such
factors as operating ambient temperature range, bias current, phase
compensation and offset adjustment method depending on the type
used. Refer to the manufacturer's data sheet or instruction manual.
Typical operational amplifiers, and buffer amplifiers:
Analog Devices: AD549, 755N/P, OP07, AD743, AD8001
National Semiconductor: LF357, LF356, LF442
Harris: HA2625, HA5160, ICL7611
Linear Tecnology: LT1360w
Sample circuits listed in this catalog introduce typical
applications of Hamamatsu photodiodes and do not cover
any guarantee of the circuit design. No patent rights are
granted to any of the circuits described herein.
PD : S2386-5K
PUT : N13T2 (NEC), TN41B (TOSHIBA), etc.
+5 V
Vo Vo
PD
C
0.01 1 k t
K PUT
A G Vg
100 k
220 k
Isc
Cf = = × [Hz]
1
t
1
Vg
Isc
4