cisco2911重置密码（Cisco2911 reset password）

cisco2911重置密码（Cisco2911 reset password） cisco2911重置密码(Cisco2911 reset password) 串口 波特率9600 无奇偶校验 8数据位 1个停止位 ================================== 终端键盘上的上电后60秒内按打破键，以便使路由器进入rommon。 rommon 1 > rommon 2 > 路由器重新启动，但忽略了保存的配置。 ====================================== 键入没有后各设置问题，或按Ctrl-C，以跳过 初始安装过程。 在路由器>提示符下键入使。 您现在的位置使能模式，应该可以看到路由器,提示。 以类型配置内存或复制启动配置配置运行配置 的非易失性RAM(NVRAM)中复制到内存中。 重要事项:请勿类型的复制运行配置配置或写入这些启动配置。 命令删除启动配置。 类型显示运行配置。 的执行命令显示了路由器的配置在显示运行配置。 这种配置，关机命令将显示所有接口下， 目前，所有的接口都关闭此外，该。 密码(启用密码，启用秘密，控制台口令，vty) 无论是经过加密或加密的格式。您可以重复使用未加密的 密码。您必须更改新的密码加密的密码。 类型配置终端。 主机名(config),提示符出现。 键入使秘密<>为了改变启用秘密密码。为 例如: 主机名(config),启用秘密 发行的每个接口上，使用没有关机命令。 如果您发出简要命令显示IP接口，每个接口 要使用应显示。 2中的值在哪里可以步骤类型配置寄存器。 或。例如: 主机名(config),配置注册 按下使用或最终离开配置模式。 主机名,提示符出现。 键入写内存或复制运行配置启动配置配置，以承诺 的变化。 密码恢复程序示例 本节提供的密码恢复过程中的一个例子。这 例如创建一个思科2600系列路由器。即使你不使用 一台思科2600系列路由器，此输出提供了一个例子，你 您的产品体验。 路由器>“启用 密码: 密码: 密码: %坏的秘密 路由器>显示版本 思科互联网络操作系统软件 iOS(TM)的C2600(c2600-is-m)软件版本12(7)，发布软件 (FC2) 版权所有(C)1986-1999思科系统公司 星期二2010年12月07日- 99 02:21 phanguye编制 图片文本的基础:0x80008088，数据底座:0x80c524f8 罗:系统的引导程序，11.3(2)版本Xa4、发布软件(FC1) 3分钟路由器的正常运行时间是 系统恢复ROM中止在PC 0x802d0b60 系统映像文件是”闪:C2600 MZ。120-7。” 思科2611(MPC860)处理器(修订0x202)26624k / 6144k字节 记忆体。 处理器板:ID jab031202nk(3878188963) m860处理器:部件号0，掩码49 桥接软件。 X.25软件，版本3.0.0。 基本速率ISDN软件1.1版。 2个以太网/ IEEE 802.3接口(S) 2个串口(同步/异步)，网络接口(S) 1综合业务数字网基本速率接口(S) 非易失性配置存储器的32k字节。 8192k处理器板系统的闪存分区1字节(读/写) 8192k处理器板系统的闪存分区2字节(读/写) 配置寄存器为0x2102 路由器> ～---该路由器刚刚开机循环，并在启动一个 ---中断序列，发送到路由器。 ～ ***系统接收到一个中断，由于打破键*** 信号= 0x3中，代码为0x500，上下文0x813ac158 PC = 0x802d0b60，矢量量0x500，SP = 0x80006030 rommon 1 > confreg 0x2142 您必须重置或电源周期，新的配置生效 rommon 2 >复位 11.3(2)系统的引导程序，版本Xa4、发布软件(FC1) 版权所有(C)1999年，由思科系统公司 交通:主页:西南:iOS的详细信息:特价 平台C2600，32768字节的主内存 程序加载完成后，进入点:0x80008000，大小:0x6fdb4c Since the image decompression: No. 1, No. . . . Number (No.) (No. 1) [determination] A statement of limitations of rights Used or copied or disclosed by the government Listed under the terms of the restriction (three) commercial computer software - limitations "Rights" clause in FAR seconds. 52.227-19 entry (C) (1) (II) the technical data and computer of the right Software terms DFARS seconds. 252.227-7013. CISCO systems, Inc. 170 West Waxman drive? The advantage of San Jose, California CISCO Internet operating system software IOS (TM) C2600 (C2600-IS-M) software version 12 (7) T, RELEASE SOFTWARE (FC2) Copyright (c) 1986-1999 CISCO systems Tuesday, December 2010, 07, -99, 02:21, phanguye The foundation of the picture text: 0x80008088, data base: 0x80C524F8 CISCO 2611 (MPC860) processor (revised 0x202) 26624K/6144K bytes Memory. Processor board: ID JAB031202NK (3878188963) M860 processor: part number 0, mask 49 Bridge software. X.25 software, version 3.0.0. Basic rate ISDN software, 1.1 edition. 2 Ethernet / IEEE 802.3 interfaces (S) 2 serial ports (synchronous / asynchronous), network interface (S) 1 ISDN basic rate interface (S) The 32K bytes of nonvolatile configuration memory. 8192K processor board system flash partitioning 1 bytes (read / write) 8192K processor board system flash partitioning 2 bytes (read / write) - - "system configuration" - What initial configuration dialog do you want to enter? [yes / no,]:N Press RETURN to begin! 00:00:19:%LINK-3-UPDOWN:BRI0 / / 0 interface, changed to UP state 00:00:19:%LINK-3-UPDOWN: interface Ethernet0 / 0, change to UP state 00:00:19:%LINK-3-UPDOWN: the interface Ethernet0 / 1 changes most when the state changes 00:00:19:%LINK-3-UPDOWN: interface Serial0 / 0, change state down 00:00:19:%LINK-3-UPDOWN: interface Serial0 / 1, change state down 00:00:20:%LINEPROTO-5-UPDOWN: line protocol interface BRI0? / 0, The state has changed downward 00:00:20:%LINEPROTO-5-UPDOWN: line protocol interface Ethernet0 / 0, The state has changed most Router > 00:00:20:%LINEPROTO-5-UPDOWN: line protocol interface Ethernet0 / 1, The state has changed most 00:00:20:%LINEPROTO-5-UPDOWN: line protocol interface Serial0 / 0, The state has changed downward 00:00:20:%LINEPROTO-5-UPDOWN: line protocol interface Serial0 / 1, The state has changed downward 00:00:50:%SYS-5 restart: reboot the system - CISCO Internet operating system software IOS (TM) C2600 (C2600-IS-M) software version 12 (7) T, RELEASE SOFTWARE (FC2) Copyright (c) 1986-1999 CISCO systems Tuesday, December 2010, 07, -99, 02:21, phanguye Zero 00 minutes 50 seconds:%LINK-5-CHANGED: interface BRI0? / 0 The state of managed shutdown has changed 00:00:52:%LINK-5-CHANGED: interface Ethernet0 / 0 The state of managed shutdown has changed 00:00:52:%LINK-5-CHANGED: interface Serial0 / 0 The state of managed shutdown has changed 00:00:52:%LINK-5-CHANGED: interface Ethernet0 / 1, The state of managed shutdown has changed 00:00:52:%LINK-5-CHANGED: interface Serial0 / 1 The state of managed shutdown has changed 00 minutes 53 seconds:%LINEPROTO-5-UPDOWN: line protocol interface Ethernet0 / 0, The state has changed downward 00:00:53:%LINEPROTO-5-UPDOWN: line protocol interface Ethernet0 / 1, The state has changed downward Router > Router > Enable Router replication, startup-config configuration, run configuration Destination file name [running configuration? 1324 bytes copied to 662 bytes / sec (2.35 seconds) Router Zero one 24 seconds:%LINEPROTO-5-UPDOWN: line protocol to interface BRI0? / 0:1, The state has changed downward Zero one 24 seconds:%LINEPROTO-5-UPDOWN: line protocol at interface BRI0 / 02, The state has changed downward Router configuration terminal Enter the configuration command, one for each line. Ending CNTL / Z. CONFIG (router) enable secret < password > Router (CONFIG) ^ Z From the console, through the console, configure zero time 01 minutes and 54 seconds:%SYS-5-CONFIG_I: A brief summary of the router IP interface Interface IP address OK? Legal state Agreement Ethernet ports Ethernet0 / 0, 10.200.40.37, YES, TFTP administration fell The undistributed TFTP is Serial0 / 0, administratively down BRI0? / 0 193.251.121.157 YES not set administratively down BRI0 / 0:1 unassigned is "not set" admin down BRI0 / 0:2 unassigned is "not set" admin down The Ethernet0 / 1 undistributed TFTP is administratively down The undistributed TFTP is Serial0 / 1, administratively down Loopback0 interface, 193.251.121.157, YES, TFTP, UP, UP Router configuration terminal Enter the configuration command, one for each line. Ending CNTL / Z. Router (configuration) interface Ethernet0 / 0 Router (configuration, if) no shutdown command Router (configuration, if) 00:02:14:%LINK-3-UPDOWN: interface Ethernet0 / 0, change to UP state 02 minutes 15 seconds:%LINEPROTO-5-UPDOWN: line protocol interface Ethernet0 / 0, The state has changed most Router (if configured) interface BRI0? / 0 Router (configuration, if) no shutdown command Router (configuration, if) Two. 26 seconds:%LINK-3-UPDOWN: interface diagram BRI0 / / 0:1, change state to next 00:02:26:%LINK-3-UPDOWN: interface diagram BRI0 / / 0:2, change state to next Two. 26 seconds:%LINK-3-UPDOWN:BRI0? / 0 interface, changed to UP state 00:02:115964116991:%ISDN-6 LAYER2UP BR0 / 0 interface: 2 layers, TEI 68 changes most Router (CONFIG) ^ Z Router 02. 35 seconds:%SYS-5-CONFIG_I: from console, through console configuration The router runs config startup-config configuration copy Destination file name [startup-config configuration? Build configuration... [OK] Display version of router CISCO Internet operating system software IOS (TM) C2600 (C2600-IS-M) software version 12 (7) T, RELEASE SOFTWARE (FC2) Copyright (c) 1986-1999 CISCO systems Compile Tuesday, -99, December 2010, 07, 2:21, by phanguye The foundation of the picture text: 0x80008088, data base: 0x80C524F8 ROM: system boot program, version 11.3 (2) XA4, RELEASE SOFTWARE (FC1) The router's normal running time is 3 minutes System recovery ROM aborted at PC 0x802D0B60 The system image file is "flash": C2600-mz.120-7.T" CISCO 2611 (MPC860) processor (revised 0x202) Bytes of memory 26624K/6144K. Processor board: ID JAB031202NK (3878188963) M860 processor: part number 0, mask 49 Bridge software. X.25 software, version 3.0.0. Basic rate ISDN software, 1.1 edition. 2 Ethernet / IEEE 802.3 interfaces (S) 2 serial ports (synchronous / asynchronous), network interface (S) 1 ISDN basic rate interface (S) The 32K bytes of nonvolatile configuration memory. 8192K processor board system flash partitioning 1 bytes (read / write) 8192K processor board system flash partitioning 2 bytes (read / write) The configuration register is 0x2142 Router configuration terminal Enter the configuration command, one for each line. Ending CNTL / Z. (CONFIG) the router configuration register is 0x2102 Router (CONFIG) ^ Z 00:03:20:%SYS-5-CONFIG_I: from the console, through the console configuration Display version of router CISCO Internet operating system software IOS (TM) C2600 (C2600-IS-M) software version 12 (7) T, RELEASE SOFTWARE (FC2) Copyright (c) 1986-1999 CISCO systems Tuesday, December 2010, 07, -99, 02:21, phanguye The foundation of picture text: 0x80008088, Data base: 0x80C524F8 ROM: system boot program, version 11.3 (2) XA4, RELEASE SOFTWARE (FC1) The router's normal running time is 3 minutes System recovery ROM aborted at PC 0x802D0B60 The system image file is "flash": C2600-mz.120-7.T" CISCO 2611 (MPC860) processor (revised 0x202) Bytes of memory 26624K/6144K. Processor board: ID JAB031202NK (3878188963) M860 processor: part number 0, mask 49 Bridge software. X.25 software, version 3.0.0. Basic rate ISDN software, 1.1 edition. 2 Ethernet / IEEE 802.3 interfaces (S) 2 serial ports (synchronous / asynchronous), network interface (S) 1 ISDN basic rate interface (S) The 32K bytes of nonvolatile configuration memory. 8192K processor board system flash partitioning 1 bytes (read / write) 8192K processor board system flash partitioning 2 bytes (read / write) The configuration register is 0x2142 (which will be reloaded in the next 0x2102) Router