威格士液压泵m2206

Revised 11/01/97 M-2206-S PVH57/63 Variable Displacement Piston Pump - 11 Design Service Data Vickers® Piston Pumps Eaton Hydraulics, Incorporated 2000 All Rights Reserved 470871 Screw Torque 64-78 N.m. (47-57 lb. ft.) 470866 Screw (4 Req’d) Torque 64-78 N.m. (47-57 lb. ft.) 474753 Screw Torque 64-78 N.m. (47-57 lb. ft.) � 396093 O-ring (2 Req’d) � Valve block (see table) Pump control (see controls pages) 471512 Pin (2 Req’d) 248935 Pin 689461 Plug (2 Req’d) Torque 12.7-13 N.m. (8.9-9.5 lb.ft.) � 513846 Gasket � 513436 Bearing S/A � 926258 Shaft spacer kit � Valve plate (see table) 913341 Locknut Torque 25-50 N.m. (18-37 lb. ft.) Maximum Adjustable Stop – S Option Standard – C/CM/CMV/CV/IC ��Rotating group kit (See table) �� Cylinder block (See table) �� 680624 Spring guide �� 627524 Spring �� 584524 Spring guide �� 85560 Retaining ring Valve block (See table) Torque Limiter – T Option Valve block (See table) � 928446 Bias piston �928448 Bias sleeve Torque 97-106 N.m (71-78 lb. ft) Grade RC30 compound � 526665 Bias spring �928447 Cap �263069 O-ring �197577 Back-up ring �262339 O-ring � 928456 Lock ring F–11–C M–11–C SF–11–C SM–11–C F–11–CT M–11–CT 928631 928632 928618 928619 860846 860847 Valve Block Table Pump Type RH LH 928679 928680 928667 928668 860855 860856 � Torque control models 860741 Adj. screw � NOTE Right hand rotation shown. View is opposite for left hand rotation. Please refer to Overhaul Manual M-2210-S. � NOTE Use shims as required to obtain 0.01–0.10 mm (.0004–.004 in.) axial shaft end play. �� 473741 Screw (4 Req’d) Torque 13-15 N.m. (9-11 lb. ft.) �� 690218 Limiter (2 Req’d) �� Piston & Shoe S/A (See table) �� Shoe cage (See table) �� 690801 Spacer (2 Req’d) 690832 Yoke S/A � 690339 Screw (2 Req’d) Torque 3.6-4.4 N.m. (2.3-3 lb. ft.) � 513885 Saddle bearing � 513886 Saddle bearing � 513433 Bearing S/A 526614 864204 883084 864313 860808 860815 864203 � 396102 O–Ring 513602 Plug Torque 97-106 N.m. (71-78 lb. ft.) � 396098 O–Ring 186580 Plug Torque 54-59 N.m. (40-43 lb. ft.) � 576601 O–Ring 470793 Screw (3 Req’d) Torque 7-9 N.m. (5-6.6 lb. ft.) 526616 Cover �513439 Shaft seal (2 Req’d if dual seal) 103824 Retaining ring (2 Req’d if dual seal) � 262355 O–Ring � 526668 Bias piston � 526665 Spring � 262355 O–Ring �� Rotating group kit (See table) � 690210 Control rod Torque 82-91 N.m. (60-67 lb. ft.) Grade RC30 compound � Available in double shaft seal kit 02–102244 02-334358 � Available in bearing kit 877423 NOTE For satisfactory service life of these components in industrial applications, use full flow filtration to provide fluid which meets cleanliness code 16/14/12 or cleaner. � 526685 Bias rod Torque 82-91 N.m. (60-67 lb. ft.) Grade RC30 compound Shaft (See table) � 690211 Control piston Available in bearing/yoke kit 02-334832 877420 Shaft Type Key 527166 1 – Straight keyed 114516 513839 2 – Splined – 883083 N – Straight keyed 472287 864342 1 – Straight key (thru) 114516 526684 2 – Spline (thru) – 913978 8 - Splined (130) – Model Designation Piston & Shoe S/A (9 req’d) Cylinder Block Shoe Cage �57 Size �63 Size 02-306362 02-306363 937023 937024 584512 860754 Note Complete replacement via rotating group kits is recommended. Non-torque control models Pump Type 57 680630 680631 57QI 514128 514121 57QP 913696 N/A 63 934442 934439 63QI 928579 860774 63QP 934443 N/A RH LH Valve Plate Table Rotating Group Kit � Available in PVH63 rotating group kit. � Available in PVH57 rotating group kit. Housing Flange/Seal -C-*S -C-*D -C2-*S -C2-*D -C3-*S -M-*S -130 suffix Housing (See table) 02–125161 02–160591 02–306056 CV CVB CMV Control Kit Pressure range 35–140 Bar 02–125160 02–125162 C CM Control Kit 140–280 Bar 35–140 Bar Pressure range 627391 Plug (2 Req’d) Torque 29-32 N.m. (21-24 lb. ft.) � 396096 O-Ring (2 Req’d) 857672 Pressure limiter spool 857673 Load sense spool � 177969 O-Ring (3 Req’d) Body (See table) 857734 Spring guide Control spring (See table) 857734 Spring guide 860750 Adj. screw (2 Req’d) � 396102 O-Ring 860749 Plug Torque 97-106 N.m. (71-78 lb. ft.) 860747 Nut (2 Req’d) Torque 14-20 N.m. (10-14 lb. ft.) 860748 Plug Torque 75-83 N.m. (55-60 lb. ft.) 473765 Screw (4 Req’d) Torque 31-37 N.m. (23-28 lb. ft.) � 396096 O-Ring 181728 Plug Torque 29-32 N.m. (21-24 lb. ft.) 857674 Spring guide 857688 Load sense spring 857679 Pin spring stop 857674 Spring guide � 396100 O-Ring 627391 Plug Torque 29-32 N.m. (21-24 lb. ft.) � 396096 O-Ring 473765 Screw (4 Req’d) Torque 31-37 N.m. (23-28 lb. ft) � 177969 O-Ring (3 Req’d) 857672 Spool 857722 Body 857734 Spring guide (2 Req’d) Control spring (See table) � 396102 O-Ring 860747 Nut Torque 14-20 N.m. (10-14 lb. ft.) 860749 Plug Torque 97-106 N.m. (71-78 lb. ft.) 860750 Adj. screw Load Sensing & Pressure Compensator Control C(M)*V Pressure Compensator Control C & CM All parts shown are included in control kit. Pressures must be set by user to circuit requirements. All parts shown are included in control kit. Pressures must be set by user to circuit requirements. Orifice plug (See table) Body Orifice Plug Control Type Spring 857733 928442 857733 – 433543 – 140–280 Bar 857681 857675 Control Type Spring 857681 857675 860750 Adj. screw 860748 Plug Torque 75-83 N.m. (55-60 lb. ft.) � 396100 O-Ring 857674 Spring guide (2 Req’d) 857679 Pin spring stop 857688 Spring Control Kit Threads Body 02–151904 inch 883386 02–151905 metric 860628 Body (see table) 627391 Plug (3 Req’d) Torque 9.8-10.2 N.m. (7.2-7.5 lb. ft.) � 396092 O-Ring (3 Req’d) 407533 Plug Torque 12.1-12.4 N.m. (8.9-9.1 lb. ft.) � 396093 O-Ring 860566 Orifice plug Torque 1.7-2.3 N.m. (1.2-1.7 lb. ft.) �113000 Plug Torque 5.1-5.9 N.m. (3.7-4.4 lb. ft.) Industrial Control (IC) 473769 Screw (2 Req’d) Torque 31-37 N.m. (23-28 lb. ft.) 473765 Screw (2 Req’d) Torque 31-37 N.m. (23-28 lb. ft.) All parts shown are included in control kit. Pressures must be set by user to circuit requirements. � NOTE IC kits pre-set to 20-30 bar differential pressure with all orifices/plugs in place. Reference Vickers Overhaul Manual M-2210-S for proper orifice/ plug configuration in various circuits prior to control installation. 860747 Nut Torque 14-20 N.m. (10-14 lb. ft.) � 396096 O-Ring �181728 Plug Torque 29-32 N.m. (21-24 lb. ft.) 939816 Spool 627391 Plug Torque 29-32 N.m. (21-24 lb. ft.) � 396096 O-Ring � 177969 O-Ring (2 req’d) � 216630 O-Ring 263497 O-ring 248845 Pin 577639 Sleeve 937272 Check valve Torque 1.7-2.3 N.m (2.3-3.1 lb. ft.) 186580 Plug Torque 54-59 N.m (73-80 lb. ft.) 262356 O-ring 860750 Adjusting Screw 860747 Nut Torque 8-10 N.m (11-14 lb. ft.) 263069 O-ring 857734 Guide Spring (See table) 913454 Spool 1649 Ball �932716Connector Torque 54-59 N.m (73-80 lb. ft.) �263497 O-ring �932716 Retainer Ring (Screw into bottom of thread) �248823 Pin 471627 Pin 217669 O-ring 177969 O-ring (2 req’d) 197594 Back-up ring 473773 Screw (4 req’d) Torque to 31-37 N.m (42-50 lb. ft.) 860655 Plug Torque 75-83 N.m (102-112 lb. ft.) 113000 Plug Torque 15-17 N.m (20-23 lb. ft.) 02–314944 02–335254 Model designation Control Kit �Torque summation parts Spring 857675 857681 860653 Body 177969 O-ring (5 req’d) 928388 Guide 913453 Guide 262356 O-ring 860749 Plug Torque 75-83 N.m (102-112 lb. ft.) Torque Limiter – T Option T**-31 T**S-31 Model designation Rear Pump LAF–11–C* LAM–11–C* RAF–11–C* RAM–11–C* LAF–11–CT LAM–11–CT RAF–11–CT RAM–11–CT 928705 928706 928730 928731 860837 860838 860828 860829 *–*BF–11–* *–*BM–11–* *–*CF–11–* *–*CM–11–* Valve block w/ SAE ‘‘A’’ Pad 474753 Screw (2 Req’d) Torque 64-78 N.m. (47-57 lb. ft.) 470866 Screw (2 Req’d) Torque 64-78 N.m. (47-57 lb. ft.) 474756 Screw (2 Req’d, SAE “A” pad) Torque 64-78 N.m. (47-57 lb. ft.) 473817 Screw (2 Req’d, SAE “B”/“C” pad) Torque 64-78 N.m. (47-57 lb. ft.) ‘‘A’’ Thru–drive ‘‘B’’ & ‘‘C’’ Thru–drive Adapter Coupling (See table) Thru–drive Adapter location (See table) Valve block (See table) O-Ring (See table) Model Designation AdapterPad Kit O-Ring CouplingTypes 401525 353264 O-Ring CouplingType 576601 8644609 tooth SAE-A 526670 876393 692934 876391876392 876390 876389 876394 Adapter Flange *A* Thru–drive SAE–A, 2–Bolt Cover Plate 939790 (Fits –031 Suffix Pumps) *AF Units use Screw 170177 (2 req’d) **AM Units use Screw 470837 (2 req’d) 1.‘‘F’’ type equal SAE threads 2. ‘‘M’’ type equal metric threads 3. ‘‘B’’ and ‘‘C’’ thru-drives created from ‘‘A’’ thru-drive pump with ‘‘B’’ or ‘‘C’’ thru-drive adapter kit installed. 4. All screws/O-rings are included with each ‘‘kit’’ to convert from ‘‘A’’ to ‘‘B’’ or ‘‘C’’ thru-drive unit. Notes: 526694 SAE-B 13 tooth 526695 SAE-BB 15 tooth 526696 SAE-C 14 tooth Typical Cross Section Position inner shaft seal facing bearing Position outer shaft seal facing shaft end Pump Startup Make sure the reservoir and circuit are clean and free of dirt and debris prior to filling with hydraulic fluid. Fill the reservoir with filtered oil to a level sufficient to prevent vortexing at suction connection to pump inlet. It is good practice to clean the system by flushing and filtering using an external slave pump. Before starting the pump, fill with fluid through one of the ports. This is par- ticularly important if the pump is above the fluid level of the reservoir. After the pump is primed, tighten the loose outlet connections, then operate for five to ten minutes (unloaded) to re- move all trapped air from the circuit. If reservoir has a sight gage, make sure the fluid is clear—not milky. Add fluid to the reservoir up to the prop- er fill level. When initially starting the pump, remove all trapped air from the system. This can be accomplished by loosening the pump outlet fittings or connections before starting the pump, or by using an air bleed valve. All inlet connections must be tight to prevent air leaks. Once the pump is started, it should prime within a few seconds. If the pump does not prime, check to make sure that there are no air leaks in the inlet line and connections. Also check to make sure that trapped air can escape at the pump outlet. Control Piston Control Rod Valve Block Port #1 Valve Block Port #2 Bias Rod Bias Piston Note Parts are shown as installed for right hand rotation. For left hand rotation, install control rod and control piston in valve block port #2. Install bias rod, bias piston and spring in valve block port #2. Spring 3 4 5 876 9 101 2 11 12 13 14 15 16 17 1 2 Piston pump, variable displacement Maximum geometric displacement 57 - 57.4 cm3/r (3.5 in3/r) 63 - 62.9 cm3/r (3.84 in3/r) Application style Blank - Mobile application (rated speed & 250/280 bar (3600-4000 psi) pressures) QI - Quiet industrial application (1500 - 1800 rpm & 250/280 bar (3600-4000 psi) pressures) QP - Quiet power unit application (1800 rpm & 140 bar (2000 psi) max. pressures – R.H. rotation only) Mounting flange, prime mover end C - SAE “C” 4–bolt type (SAE J744-127-4 ) C2 - Optional combination 2- & 4-bolt SAE-C pilot C3 - Optional 4-bolt SAE-C pilot for vertical pump mounting M - Optional metric 4-bolt pilot ISO 3019/2-125B4HW (Must be used with ‘N’ shaft option.) Shaft rotation, viewed at prime mover end R - Right hand, clockwise L - Left hand, counterclockwise Configuration Blank - Non-thru-drive (single pump) A - SAE-A thru-drive pump, standard (SAE J744-82-2) B - SAE-B thru-drive pump, optional (SAE J744-101-2/4) C - SAE-C thru-drive pump, optional (SAE J744-127-2/4) S - Adjustable maximum volume stop (‘‘S’’ option not available on thru-drive and torque control pump models.) 3 4 5 6 7 8 9 10 11 12 13Main ports F - SAE 4-bolt flange ports (standard) M - SAE 4-bolt pads with metric mounting bolt threads Shaft-end type, at prime mover end N - Metric ISO short straight key (ISO 3019/2-E32N for ‘‘M’’ pilot only) 1 - SAE-C straight key 2 - SAE-C 14 tooth spline 8 - SAE-BB, 15 tooth spline Shaft seal, prime mover end S - Single, one-way D - Double, two-way Pump design number 11 - (Subject to change. Installation dimensions unaltered for design numbers 10 to 19 inclusive. ) Pressure control type C - Compensator, 140-280 bar (2000-4000 psi) CM - Compensator, 35-140 bar (500-2000 psi) IC - CETOP 3 interface compensator, 20 bar factory ‘‘differential’’ pressure setting (QI and QP models only) Factory compensator pressure setting Blank - Leave blank for ‘‘IC’’ controls only 7 - 70 bar (1015 psi) normal ‘‘CM7’’ setting (all pump sizes) 23 - 230 bar (3335 psi) normal ‘‘C23’’ setting (63, 81, 106, 141 models) 25 - 250 bar (3625 psi) normal ‘‘C25’’ setting (57, 74, 98, 131 models) Optional pressure control functions Blank - Leave blank for basic compensator controls of IC models. V - Load sensing, 20 bar (290 psi) factory ‘‘differential’’ pressure setting T - Torque limiting control (Used with sections and . VT - Load sensing with torque limiting VB - Load sensing with internal bleed down (0.15” dia. orifice) VBT- Load sensing with internal bleed down and torque limiting Torque limiting control pressure setting Blank - Leave blank if no torque limiting control is used 4 - Standard minimum 40 bar setting of ‘‘T’’ torque control option Torque limiting control summation Blank - Standard torque control S - Optional torque control with summation feature Control design number 31 - All control options Special feature suffix 031- Mounting with SAE-A, 2-bolt cover plate 130- PVH57/63 with SAE-B, 4.00 inch dia. pilot, 2/2-bolt mount. Both 2-bolt patterns are rotated 45 degrees from port center line. 14 15 16 17 Model Code 14 15 Printed in U.S.A.