Nokia_Lumia_710拆机维修手册

Nokia_Lumia_710拆机维修 Service Manual for L1 and L2 Nokia Lumia 710 RM-803 RM-809 Key features z Windows Phone Mango operating system z Large 3.7 LCD TFT ClearBlack screen not OLED z Sync store and share media files z Best instant social experience z Fast browsing with IE9 Version 1.0Exploded view Disassembly steps Disassembly video More More MoreAssembly hints Assembly hints video Service devices More More MoreSolder components Product controls and interfaces Service concept More More MorePhone reset More 2011 Nokia Confidential All Rights Reserved.Service Manual Level 1 and 2Nokia Lumia 710 Exploded viewRM-803 RM-809Version 1.0 A-COVER ASSEMBLY I0001 I0002 I0004 A-COVER I0004 DISPLAY I0005 EARPIECE I0003 2 LIGHT SWAP PACKAGE I0006 - I0011 UI KEYMAT DOMESHEET I0007 DISPLAY CONDUCTIVE TAPE LIGHT SWAP PWB I0006 I0008 DIPRO GASKET I0010 SHIELD ADHESIVE I0011 CAMERA I0013 USB BOOT I0012 CAMERA LENS BOOT I0014 FLASH SUPPORT 3 I0025 MAIN CHASSIS ASSEMBLY IHF SPEAKER I0015 - I0022 I0015 LED FLASH I0018 SPEAKER GASKET I0016 FLASH BOOT MAIN ANTENNA I0019 I0021 AV JACK I0017 MAIN CHASSIS I0022 TYPE LABEL I0009 CAMERA CROSS SCREW I0023 BATTERY COVER I0024 Only available Not reuseable Repair/swap v1.0 as assembly after removal only in level 3 2011 Nokia Confidential All Rights Reserved.Service Manual Level 1 and 2Nokia Lumia 710 Disassembly stepsRM-803 RM-809Version 1.0 For disassembling you need the Nokia Standard Toolkit version 2. You will also need the camera removal tool SS-278 and an AV plug. Protect the A-COVER with protective film.Use the opening notch on the left side of the device to release the BATTERY COVER.Remove the BATTERY COVER.Unscrew the eleven camera cross screws in the order shown. Do not use them again. Discard them.Push the MAIN CHASSIS slightly forward and lift up the bottom end. Remove the MAIN CHASSIS.Remove the CAMERA LENS BOOT with tweezers. Use plastic tweezers if available.Remove the FLASH SUPPORT with tweezers.Open the TOUCH WINDOW connector with the SS-93. Be careful not to damage the connector.Use the SS-93 to lift up and push forward the ENGINE BOARD from the shown place. Be careful not todamage the shown springsThen carefully turn over the engine board as shown. While turning the ENGINE BOARD be careful not todamage the two shown connectors.Open the DISPLAY connector with the SS-93. Be careful not to damage the connector or componentsnearby.The ENGINE BOARD can now be separated.Lift up the EARPIECE with the dental tool. Be careful not to injure yourself with the sharp end of thedental tool.Remove the EARPIECE with tweezers. When removing the EARPIECE make sure not to touch the shownpart of it.Use the SS-93 to release the DISPLAY. Start from the shown corner. Lift the corner and hold it up for awhile. The adhesive on the DISPLAY GASKET will slowly loosen up making it easier to remove the DISPLAY.Be careful not to bend the DISPLAY or damage the TOUCH WINDOW connector.Work around the DISPLAY with the SS-93 to release it completely.Lift up and remove the DISPLAY. In case the shown tape is peeled off from the DISPLAY and remains onthe A-COVER the driver on the DISPLAY may be damaged. In this case discard the DISPLAY.If the tape is not damaged and stays on the DISPLAY continue the disassembly without discarding theDISPLAY. Protect the DISPLAY with protective film.Use the sharp end of the SS-93 to peel out one corner of the DISPLAY GASKET.Remove the DISPLAY GASKET with tweezers. Do not use it again. Discard it.Protect the other side of the A-COVER with protective film.Remove the AV JACK with an AV plug.Release the IHF SPEAKER with the dental tool.Remove the IHF SPEAKER with tweezers. Do not use it again. Discard it.Release the SPEAKER GASKET with the dental tool and remove it with tweezers. Do not use it again.Discard it.Push out the LED FLASH with the sharp end of the SS-93.Remove the LED FLASH and the FLASH BOOT with tweezers.Separate the LED FLASH from the FLASH BOOT.Push down the camera removal tool SS-278 until the camera retaining clips are released. Hold from theshown sides of the SS-278.Then lift up and remove the CAMERA.Remove the USB BOOT.Remove the three shown SHIELD ADHESIVES with tweezers. Do not use them again. Discard them.Use tweezers to remove the UI KEYMAT DOMESHEET. Be careful not to touch the MICROPHONE Do notuse the UI KEYMAT DOMESHEET again. Discard it.Use the SS-93 to peel off the DISPLAY CONDUCTIVE TAPE. Do not use it again. Disard it.Make sure that the whole DISPLAY CONDUCTIVE TAPE and the adhesive remains are removed from theENGINE BOARD.