模具专业术语

模具专业术语 模具述语 一、 入水:gate 撑头: support pillar 进入位: gate location 唧嘴: sprue bushing 水口形式:gate type 挡板:stop plate 大水口:edge gate 定位圈:locating ring 细水口: pin-point gate 锁扣:latch 水口大小:gate size 扣鸡:Parting lock set 转水口: Switching runner/gate 推杆:push bar 唧嘴口径: sprue diameter 栓打螺丝:S.H.S.B 二、流道: runner 顶板:ejector rod 热流道: hot runner,hot manifold 活动臂:lever arm 热嘴冷流道: hot sprue/cold runner 分流锥:spure sperader 唧嘴直流: direct sprue gate 水口司:bush 圆形流道:round(full/half runner 垃圾钉:stop pin 流道电脑分析:mold flow analysis 隔片:buffle 流道平衡:runner balance 弹弓柱:spring rod 热嘴: hot sprue 弹弓:die spring 热流道板:hot manifold 中托司:ejector guide bush 发热管:cartridge heater 中托边:ejector guide pin 探针: thermocouples 镶针:pin 插头: connector plug 销子:dowel pin 插座: connector socket 波子弹弓:ball catch 密封/封料: seal 喉塞: pipe plug 三、运水:water line 锁模块:lock plate 喉塞:line lpug 斜顶:angle from pin 喉管:tube 斜顶杆:angle ejector rod 塑胶管:plastic tube 尼龙拉勾:parting locks 快速接头:jiffy quick connector plug/socker 活动臂:lever arm 四、模具零件: mold components 复位键、提前回杆:early return bar 三板模:3-plate mold 气阀:valves 二板模:2-plate mold 斜导边:angle pin 边钉/导边:leader pin/guide pin 术语:terms 边司/导套:bushing/guide bushing 承压平面平衡:parting surface support balance 中托司:shoulder guide bushing 模排气:parting line venting 中托边L:guide pin 回针碰料位:return pin and cavity interference 顶针板:ejector retainner plate 模总高超出啤机规格:mold base shut hight 托板: support plate 顶针碰运水:water line interferes withejector pin 螺丝: screw 料位出上/下模:part from cavith (core) side 管钉:dowel pin 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 开模槽:ply bar scot 不准用镶件: Do not use (core/cavity) insert 内模管位:core/cavity inter-lock 用铍铜做镶件: use beryllium copper insert 顶针: ejector pin 初步(正式)模图设计:preliinary (final) mold design 司筒:ejector sleeve 反呵:reverse core 司筒针:ejector pin 弹弓压缩量:spring compressed length 推板:stripper plate 稳定性好:good stability,stable 缩呵:movable core,return core core puller 强度不够:insufficient rigidity 扣机(尼龙拉勾):nylon latch lock 均匀冷却:even cooling 斜顶:lifter 扣模:sticking 模胚(架): mold base 热膨胀:thero expansion 上内模:cavity insert 公差:tolorance 下内模:core insert 铜公(电极):copper electrode 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate