凯越ABS灯常亮

凯越ABS灯常亮 For jetta vehicle ABS warning light and hand brake light phenomenon, according to the control unit maintenance case most of the reasons is the failure, some cases also plug corrosion or loose caused the control unit 1, the reason that the hand brake lamp is bright may be because of the previous brake, the brake oil too little, the hand brake switch failed to cause. You can check the brake, brake and brake switch. The reason for the light of ABS may be the problem of the wheel ring sensor of ABS, failure codes and so on. The wheel ring sensor of ABS can be checked, the repair instrument is used to extract the fault code and the error code is eliminated. ABS or EBD fault occurs -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- The hand brake is bright with the ABS lamp, indicating that EBD has a malfunction and has just read the instructions See if the plug for the ABS pump is loose. It should be falling Child dynamic allocation (EBD) The system EBD system enables the rear brake to provide a greater proportion of the power, which maximizes the efficiency of each brake. It works by adjusting the load condition and speed of the car to the rear wheels. The EBD system is an integral part of the ABS system and USES certain parts of the ABS system to perform the function of optimizing the distributive power. The EBD system will also stop working if any of the ABS system components used by EBD functions fail. When the EBD system is working, you may hear a tremor of noise or a slight vibration of the brake pedal, which is normal and not a failure. The steps taken during the failure of the noil EBD system If the EBD system fails, the system will stop working, the brake system alarm lights and the ABS alarm lights will be lit. During driving, the EBD system may fail if the brake system alarm lights and ABS alarm lights are also lit. Even if the EBD system fails, the conventional braking system will still work. However, when the brake pedal is more likely to be carried on by the rear wheels than normal, the rear wheels will be more likely to die, and the movement of the car may become more difficult to control. If the brake system alarm lights and ABS alarm lights are also lit, follow these steps: Park your car in the nearest safe and flat place. Turn off the engine, apply the car brake, and restart the engine. 3. Loosen the parking brake, if two alarm lights, EBD system may have a fault, we recommend that you carefully will drive to the nearest SUBARU dealer, inspection on the system. 4. If, after restarting the engine two alarm lamp light and will remain lit again, can shut down the engine once again, apply the parking brake, then check that the brake fluid level. 5. If the brake fluid level is not lower than "MIN" mark, the EBD system may have fault, we recommend that you carefully will drive to the nearest SUBARU dealer inspection on the system. If the liquid level of the brake fluid is below the "MIN" sign, then the car is not allowed to drive. Instead, we suggest that you drag the car to the nearest SUBARU dealer for maintenance. ! warning It is dangerous to drive a car when the lights are lit, because this means that the car's braking system may not work properly. If the lights continue to light, we recommend that you ask the SUBARU dealer to check all the brakes immediately. If you can't judge whether the brake is working To be normal, do not drive the car, we suggest you drag the car to the nearest SUBARU dealer for maintenance. Your car on the road first hand brake lights and ABS lamp at the same time, really belongs to the excessively high transient voltage generator for vehicle system voltage is greater than the set the highest voltage of the ABS system, so the trouble light lit up the system, first of all, appear this kind of fault on the car's electrical system is certainly have an impact, because the voltage as possible for some of the vehicle electrical system is damaged, it is recommended that you will be best generator timely replace, to avoid damages to the other electrical system of the vehicle, 08 the ABS lamp is always bright [fixed]! Today, I will take a 2008 car. Failure phenomenon, the ABS lamp is always bright, start off the code, the problem begins! You can't detect the ABS system with KT600! The 2008 model is similar to the ABS structure of the old cato, and recently tested the car's ABS system. To test! The car owner, after buying a car, added a full set of hernia lights, far and near light in the decorative shop. This is what I think is this: the damned hernia lamp: the module that affects ABS! Just guess! W1a e % % 0 f B check circuit, the power of the diode is used to inspect the main power supply and open the key, normal, doubt can't load, change into the 21 w lamp, the result is no problem! Here's a note: the body is pressing the fuse box in the engine room, checking ABS's plug! Since the power supply is OK, so look at the data lines, in the diagnosis of a place, find the root of purple white cable voltage of 2.0 V or so, remove the plug of the ABS, voltage disappeared, data line basic normal! Generally do this, also can only doubt ABS computer! Think about the buick circuit problem, a lot of it is a line problem, so on a reinspection power! This time the method has changed; Don't pull the plug to detect the power supply. , At this moment the heart is pleased; There is no power supply [60A's main power supply]! Don't be anxious to find a problem, just give it a power source, then go in and look at the instrument, and after a few seconds the ABS lamp goes out! Follow the line check, finally find the single plug of the main power line of ABS at the bottom of the box is not good! Troubleshooting after processing! First, ensure the normal order of the power battery is normal, firewire and body ground. Normal hand brake lights may be brake oil. There is something wrong with the hand brake switch and line. Abs with voltage of relationship. In is four sensor check sensor resistance and dirt. Prevent arms control system failure is mostly in the system wiring plug loose or poor contact, conductor is open circuit or short circuit, open circuit or short circuit, electromagnetic valve coil electric pump circuit open circuit or short circuit, electromagnetic wire wheel speed sensor duration of electrical internal circuit or open circuit or short circuit, short circuit, and the brake switch, pressure switch and liquid level switch can't work normally. In addition, the battery voltage is too low, the wheel speed sensor and gear ring between the gap is too big or chamber were stained with mud and reservoir level too low will affect the system's normal work.