炭黑英文msds

炭黑英文msds ,,,MATERIAL SAFETY DATA SHEET,,, 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING Product Name: CARBON BLACK N330 Synonyms: Carbon Black, Furnace Black Use of the Substance/Preparation: Various, Industrial Products Supplier: Carbon Black Co. ,Ltd. City, China TEL: FAX:0 2. HAZARDS IDENTIFICATION Indication of danger: Hazardous according to the Worksafe Australia designated list of hazardous substances. Xn - Harmful. C3 - Carcinogen Category 3. Principle Routes of Exposure: Inhalation, Eye contact, Skin contact POTENTIAL HEALTH EFFECTS Eye Contact: May cause mechanical irritation. Irritating, but will not permanently injure eye tissue.Low hazard for usual industrial or commercial handling. Skin Contact: No adverse effects expected. Inhalation: Dust may be irritating to respiratory tract. Provide appropriate exhaust ventilation at machinery and at places where dust can be generated. See also Section 8. Ingestion: Health injuries are not known or expected under normal use. Low hazard for usual industrial or commercial handling. Carcinogenic Effects: Substance listed by IARC (International Agency for Research on Cancer). See also Section 9. Target Organ Effects: Lungs Medical Conditions Aggravated by Exposure: Asthma, Respiratory disorder 1 Potential Environmental Effects: No special environmental precautions required. Not soluble in water. See also Section 12. 3. COMPOSITION/INFORMATION ON INGREDIENTS 4. FIRST AID MEASURES Skin Contact: Wash thoroughly with soap and water. Seek medical attention if symptoms develop. Eye Contact: Flush eyes immediately with large amounts of water for 15 minutes. Seek medical attention if symptoms develop. Inhalation: If cough, shortness of breath or other breathing problems occur, move to fresh air. Seek medical attention if symptoms persist. If necessary, restore normal breathing through standard first aid measures. Notes to Physician: Treat symptomatically. 5. FIRE-FIGHTING MEASURES Extinguishing Media: Use foam, carbon dioxide (CO2), dry chemical or water spray. A fog is recommended if water is used. DO NOT USE a solid water stream as it may scatter and spread fire. Special Protective Equipment for Firefighters: Wear suitable protective equipment. In the event of fire, wear self-contained breathing apparatus. Specific Hazards: It may not be obvious that carbon black is burning unless the material is stirred and sparks are apparent. Carbon black that has been on fire should be observed closely for at least 48 hours to ensure no smoldering material is present. Burning produces irritant fumes. The product is insoluble and floats on water. If possible, try to contain floating material. This material creates a fire hazard because it floats on water. Hazardous Decomposition and/or Combustion Products: Carbon monoxide, Carbon dioxide, Oxides of sulphur, Organic products of decomposition. Risk of Dust Explosion: Do not create a dust cloud by using a brush or compressed air. 2 Chemical Name CAS Number EINECS/ELINCS Weight % EU Classification Carbon Black 1333-86-4 215-609-9 100 None 6. HANDLING AND STORAGE Handling: Avoid contact with skin and eyes. Do not breathe dust. Provide appropriate exhaust ventilation at machinery and at places where dust can be generated. Do not create a dust cloud by using a brush or compressed air. Fine dust is capable of penetrating electrical equipment and may cause electrical shorts. Take precautionary measures against static discharge. Storage: Keep in a dry, cool and well-ventilated place. Keep away from heat and sources of ignition. Do not store together with strong oxidizing agents. Do not store together with volatile chemicals as they may be adsorbed onto product. Keep in properly labeled containers. 7. PHYSICAL AND CHEMICAL PROPERTIES Appearance: Black Pellets Odor: None pH: 7-10(non-oxidized carbon black) Density: 1.7 - 1.9 g/cm? @ 20?C Bulk Density: 20 - 550 kg/m3 Specific Gravity: Not determined Boiling Point/Range: Not applicable Melting Point/Range: Not applicable Vapor Pressure: Not determined Water Solubility: Soluble % Volatile (by Weight): < 2.5% @ 950?C (non-oxidized carbon black) Evaporation Rate: Not applicable Viscosity: Not determined Partition Coefficient (n-octanol/water): Not determined Flash Point: Not applicable Method: Not applicable Explosion Limits in Air - Upper (%): Not determined Explosion Limits in Air - Lower (%): 50 g/m3 (dust) Autoignition Temperature: > 140?C (transport) 3 Method: IMDG-Code Minimum Ignition Temperature: > 350?C (BAM Furnace) Burn Velocity: > 45 seconds(Not classifiable as "Highly Flammable” or "Easily Ignitable") Flammability Classification: Not applicable 8. STABILITY AND REACTIVITY Stability: Stable. Reactivity: May react exothermically upon contact with strong oxidizers Incompatible Materials: Strong oxidizers such as chlorates, bromates, and nitrates. Hazardous Polymerization: Hazardous polymerization does not occur. Mechanical Sensitivity (shock): Not sensitive to mechanical impact. Conditions to Avoid: Do not expose to temperatures above 300?C. Keep away from oxidizing agents in order to avoid exothermic reactions. Hazardous Decomposition and/or Combustion Products: Carbon monoxide, Carbon dioxide, Oxides of sulphur, Organic products of decomposition. Static Discharge Effects: Take precautionary measures against static discharges. Avoid dust formation. All metal parts of the mixing and processing equipment must be earthed/grounded. Ensure all equipment is electrically earthed/grounded before beginning transfer operations. 9. TOXICOLOGICAL INFORMATION ACUTE TOXICITY Oral LD50: LD50/oral/rat = > 8000 mg/kg. Eye Irritation: Rabbit. Draize score 10-17/110 @ 24 hr. Non-irritating. Skin Irritation: Rabbit. 0.6/8. Slight irritation. SUBCHRONIC TOXICITY Rat, inhalation, duration 90 days NOAEL = 1.0 mg/m3 Target organ: lungs Effect: inflammation, hyperplasia, fibrosis. CHRONIC TOXICITY Rat, oral, duration: 2 years Effect: no tumors Mouse, oral, duration: 2 years 4 Effect: no tumors Mouse, dermal, duration: 18 months Effect: no skin tumors Rat, inhalation, duration: 2 years Target organ: lungs Effect: inflammation, fibrosis, tumors Note: Tumors in the rat lung are related to the fine particle overload phenomenon rather than to a specific chemical effect of the dust particles in the lung. These effects in rats have been reported in studies on other inorganic insoluble particles and appear to be species specific. Tumors have not been observed in other species (i.e., mouse and hamster) for other insoluble particles under similar circumstances and study conditions. Carcinogenic Effects: Substance listed by IARC (International Agency for Research on Cancer). Does not contain any substances listed by NTP (National Toxicology Program), OSHA (Occupational Safety and Health Administration), ACGIH (American Conference for Governmental Industrial Hygienists) or EU (European Union). Carbon Black IARC Statement: In 1995 International Agency for Research on Cancer (IARC) concluded, "There is inadequate evidence in humans for the carcinogenicity of carbon black." Based on rat inhalation studies, IARC concluded that there is "sufficient evidence in experimental animals for the carcinogenicity of carbon black", resulting in their classifying carbon black as "possibly carcinogenic to humans (Group 2B)". Carbon black is not designated a carcinogen by the U.S. National Toxicology Program (NTP), the U.S. Occupational Safety and Health Administration (OSHA), the American Conference of Governmental Industrial Hygienists (ACGIH) or the European Union (EU). The U.S. National Institute of Occupational Safety and Health (NIOSH) 1978 criteria document on carbon black recommends that only carbon blacks with polycyclic aromatic hydrocarbon (PAH) levels greater than 0.1% require the measurement of PAHs in air. As some PAHs are possible human carcinogens, NIOSH recommends an exposure limit of 0.1 mg/m3 for PAHs in air, measured as the cyclohexane-extractable fraction. Epidemiology: Results of epidemiological studies of carbon black production workers suggest that cumulative exposure to carbon black may result in small decrements in lung function, as measured by FEV1. In addition to normal age related decline in the FEV1 of approximately 1200 ml over 40 years, according to a European investigation, exposure to 1 mg/m3 (inhalable fraction) of carbon black over a 40-year lifetime will result in an additional 48 milliliter (ml) decline in FEV1. Asimilar morbidity study in the United States suggested a 27 ml decline in FEV1 from a 1mg/m3 exposure over a 40-year period. The relationship between symptoms and exposure to carbon black is less clear. In the U.S. study, 9% of the highest exposure group (in contrast to 5% of the unexposed group) reported symptoms consistent with chronic bronchitis. In the European study, methodological limitations in the administration of the questionnaire limit the drawing of definitive conclusions about symptoms. This study, however, indicated a link between carbon black and small opacities on the chest films, with negligible effects on lung function. A study of carbon black workers in the UK showed an elevated incidence of lung cancer but it was not considered to be related to carbon black exposure. A study of workers at a large German carbon black manufacturing facility found increased lung cancer mortality among German carbon black workers, but found no apparent dose-response relationship between lung cancer mortality and several indicators of occupational exposure, including years of employment and carbon black exposure. The study concluded that the high lung cancer mortality could not be fully explained by selection, smoking, or other occupational risk factors, but the results also provided little evidence for an effect from carbon black exposure. A recent mortality study of US carbon black workers found no association between employment in carbon black production and lung cancer or any other type of cancer. Mutagenic Effects: A dimethylsulfoxide (DMSO) suspension of carbon black produced negative results in an Ames test. Organic solvent extracts of carbon black, however, can contain traces of 5 polycylic aromatic hydrocarbons (PAH), which may affect the results in different in-vitro test systems. In an experimental investigation, mutational changes in the hprt gene were reported in alveolar epithelial cells in the rat following inhalation exposure to carbon black. This observation is believed to be rat specific and a consequence of "lung overload" (see Chronic Toxicity above). Reproductive Toxicity: Did not show effects in animal experiments. Sensitizing Effects: Contains no known sensitizers. Synergistic Materials: None reasonably foreseeable. 10. ECOLOGICAL INFORMATION Aquatic Toxicity: Fish (Brachydanio rerio): LC50 (96hr) > 1,000 mg/L. (Method: OECD 203). Daphnia magna: EC50 (24hr) > 5,600 mg/L. (Method: OECD 202). Algae (Scenedesmus subspicatus): EC50 (72hr) > 10,000 mg/L. Algae (Scenedesmus subspicatus): NOEC >= 10,000 mg/L. Activated sludge: EC0 (3hr) >= 800 mg/L. (Method: DEV L3 TTC test). ENVIRONMENTAL FATE Mobility: Not expected to migrate. Insoluble. Bioaccumulation: Not expected due to physicochemical properties of the substance. Persistence / Degradability: Not expected to degrade. Distribution to Environmental Compartments: Insoluble. Expected to remain on soil surface. 11. DISPOSAL CONSIDERATIONS Product, as supplied, should be disposed of in accordance with the regulations issued by the appropriate federal, state and local authorities. Same consideration should be given to containers and packaging. 12. TRANSPORT INFORMATION The following organizations do not classify carbon black as a "hazardous cargo" if it is "carbon, non-activated, mineral origin". Cabot carbon blacks meets this definition. - Canadian Transport of Dangerous Goods Regulation - European Transport of Dangerous Goods Regulation - GGVS, GGVE, RID, ADR, IMDG Code, ICAO-TI - United Nations (no UN number) - US Department of Transportation CAS NO 1333-86-4 UN Number: 1361 UN Proper Shipping Name: Not classified UN Shipping Class: Not classified 6 UN Packing Group: Not classified International Transportation Identification: "Carbon black, non-activated, mineral origin". Not dangerous according to IMDG-Code. Not dangerous according to ICAO-TI. US Rail Regulations: Not classified 13. ACCIDENTAL RELEASE MEASURES Personal Precautions: CAUTION: Wet carbon black produces slippery walking surfaces. Avoid dust formation. Ensure adequate ventilation. Use personal protective equipment. See also Section 8. Methods for Cleaning Up: Clean up promptly by vacuum. Use of a vacuum with high efficiency particulate air (HEPA) filtration is recommended. Do not create a dust cloud by using a brush or compressed air. Pick up and transfer to properly labelled containers. See Section 13. Environmental Precautions: Do not allow material to contaminate ground water system. The product is insoluble and floats on water. If possible, try to contain floating material. Local authorities should be advised if significant spillages cannot be contained. 14. EXPOSURE CONTROLS / PERSONAL PROTECTION EXPOSURE LIMITS The table below is a summary. Please see the specific legislation for complete information. Carbon Black, CAS RN 1333-86-4: Australia: 3.0 mg/m3, TWA Belgium - OEL: 3.6 mg/m3, TWA Canada: 3.5 mg/m3, TWA China: 4.0 mg/m3, TWA 8.0 mg/m3, STEL Finland: 3.5 mg/m3, TWA 7.0 mg/m3, STEL France - INRS: 3.5 mg/m3, TWA/VME Germany - TRGS 900: 3.0 mg/m3, respirable TWA 10.0 mg/m3, inhalable TWA Germany - MAKs: 1.5 mg/m3, respirable TWA 4.0 mg/m3, inhalable TWA Ireland: 3.5 mg/m3, TWA 7.0 mg/m3, STEL Italy - OEL: 3.5 mg/m3, TWA Korea: 3.5 mg/m3, TWA Netherlands - MAC: 3.5 mg/m3, TWA 7 Norway: 3.5 mg/m3, TWA Spain: 3.5 mg/m3, TWA Sweden - TLV: 3.0 mg/m3, TWA United Kingdom - WEL: 3.5 mg/m3, inhalable TWA (a) 7.0 mg/m3, inhalable STEL US ACGIH - TLV: 3.5 mg/m3, TWA US OSHA - PEL: 3.5 mg/m3, TWA Note: Unless otherwise indicated as "respirable" or "inhalable", the exposure limit represents a "total" value. The inhalable exposure limit has been demonstrated to be more restrictive than the total exposure limit, by a factor of approximately 3. 15. STABILITY AND REACTIVITY Stability: Stable. Reactivity: May react exothermically upon contact with strong oxidizers. Cabot Corporation ___________________________________________________________________ ______ Product Name: REGAL， 250R Product Code: R250R Revision Date: 18/June/2007 Page 6 of 10 Incompatible Materials: Strong oxidizers such as chlorates, bromates, and nitrates. Hazardous Polymerization: Hazardous polymerization does not occur. Mechanical Sensitivity (shock): Not sensitive to mechanical impact. Conditions to Avoid: Do not expose to temperatures above 300?C. Keep away from oxidizing agents in order to avoid exothermic reactions. Hazardous Decomposition and/or Combustion Products: Carbon monoxide, Carbon dioxide, Oxides of sulphur, Organic products of decomposition. Static Discharge Effects: Take precautionary measures against static discharges. Avoid dust formation. All metal parts of the mixing and processing equipment must be earthed/grounded. Ensure all equipment is electrically earthed/grounded before beginning transfer operations. 16. OTHER INFORMATION Carbon Black Extracts: Manufactured carbon blacks generally contain less than 0.1% of solvent extractable polycyclic aromatic hydrocarbons (PAH). Solvent extractable PAH content depends on numerous factors including, but not limited to, the manufacturing process, desired product specifications, and the analytical procedure used to measure and identify solvent extractable 8 materials. Questions concerning PAH content of carbon black and analytical procedures should be addressed to your carbon black supplier. General Information: The carbon black industry continues to sponsor research designed to identify adverse health effects from long term exposure to carbon black. This MSDS will be updated as new safety and health information may become available. 9