6X6四脚轻触按键规格书

CUSTOMER : REF.NO : DATE : 200 . . MODEL : TACT SWITCH MODEL No. : 1102 PAGE 2 3 ~6 INDEX DRAWING SPECIFICATION 주식회사 대진산업 DAEJIN INDUSTRY CO.,LTD Approved by Remark APPLICATION DSN CHK APP M.K.R M.K.J K.Y.I RoHS PQS-1001-10(REV.0) DAEJIN INDUSTRY CO., LTD A4(210×297) PAGE 2 / 6 PQS-1001-10(REV.0) DAEJIN INDUSTRY CO., LTD A4(210×297) 1. General Relative humidity : 65±5%RH 2. Performance 2.1 Electrical characteristics bounce shall be tested at 'ON' and 'OFF' 10msec Max. Air pressure : 86 ~ 106kpa (860 ~ 1060mbar) 2.1.4 Bounce Relative humidity : 45 ~ 85%RH TEST CONDITIONS PERFORMANCE encountered in normal use (3 to 4 operation per sec.) There shall be no Lightly striking the center of the stem at a rate Voltage terminals and across terminals and frame for one minute. breakdown 1.4 Appearance and dimensions : See outside drawing page 1.5 Standard conditions : Unless otherwise specified, the test and measurements shall Dielectric 2.1.3 Withstanding AC 250V (50Hz or 60Hz) shall be applied across and frame for one minute. 2.1.2 Resistance DC 100V potential across terminals and across terminals 100MΩ Min. lnsulation Measurements shall be made following application of Resistance a 1kHz small-current contact resistance meter. Applying a static load twice the actuating force to the 2.1.1 Contact center of the stem, measurements shall be made with 100mΩ Max. under the above-mentioned conditions, the following conditions ITEMSNO. DSN be carried out as follows : Ambient temperature : 5 ~ 35℃ However, if doubt arises on the decision based on the measured values DJT 1102 PAGE 1 OF 4 TACT SWITCH SPECIFICATION DATE 2006.08.07 shall be employed. PAGE 3 / 6 CHK APP M.K.JK.M.S Ambient temperature : 20±2℃ Air pressure : 86 ~ 106kpa (860 ~ 1060mbar) 1.1 Switch rating : DC 12V, 50mA 1.2 Operation temperature range : -20℃ ~ 70℃ 1.3 Preservative temperature range : -30℃ ~ 80℃ MODEL K.Y.I MODEL No. Oscill o scope5V S/W 5kΩ PQS-1001-10(REV.0) DAEJIN INDUSTRY CO., LTD A4(210×297) 2.2 Mechanical characteristics PAGE 4 / 6 DSN Soldering temperature : 260±5℃ PAGE ITEMS TEST CONDITIONSNO. MODEL TACT SWITCH SPECIFICATION DATE DJT 1102MODEL No. 2 OF 4 K.Y.I 2006.08.07 APP PERFORMANCE K.M.S CHK M.K.J Push by recommended operating condition 2.2.1 Operation Force See outside drawing page Push by recommended operating condition F = (Operation force) × 2 2.2.2. Travel 0.25 ±0.1 mm 2.2.3 Stop Strength A static load of 3kgf shall be applied in the direction of No damage (Electrical stem operation for a period of 60 seconds. and Mechanical) (1) Amplitude : 1.5mm (2) Sweep rate : 10-55-10Hz for 1 minute. No. 2.1 and 2.2.1 to 2.2.4 Vibration Test (3) Sweep method : Logarithmic frequency sweep rate. 2.2.2 shall be satisfied. (4) Vibration direction : X.Y.Z (3 directions). (5) Time : Each direction 2 hours (Total 6 hours). (1) Acceleration : 80G (2) Cycles of test : 3 cycles each in 6 directions for a total 18 cycles. No. 2.1 and 2.2.1 to 2.2.5 Impact Shock Test 2.2.2 shall be satisfied. and Mechanical) Soldering area : t/2 of P.W.B thickness 2.2.6 Soldering heat test (P.W.B : t = 1.6) No damage (Electrical Soldering time : 5±1 sec Travel Travel Push force Return force Force PQS-1001-10(REV.0) DAEJIN INDUSTRY CO., LTD A4(210×297) 2.3 Climatic characteristics (3) Duration of test : 48 hours (2) Salt solution : 5 ± 1% or discoloration Switch shall be checked after following test. Without excessive rust 2.3.6 Salt mist test (1) Temperature : 35±2℃ shall be satisfied. No. 2.1.2 to 2.1.3 & 2.2.2 initial value ±30% 2.3.5 Operating Life Test (4) Cycles of operation : See outside drawing page Operating force : (3) Push force : Maximum value of operation force Bounce : 20m sec max. (2) Operation speed : 2 ~ 3 cycles/sec : 200mΩ max. (1) DC 5V, 5mA Resistance load Contact Resistance (5) Standard conditions after test : 1 hour (4) Take off a drop water to 2.2.2 shall be satisfied. 2.3.4 Humidity Test (3) Duration of test : 96 hours No. 2.1.2 to 2.1.4 & 2.2.1 (2) Relative humidity : 90 ~ 95% : 200mΩ max. (1) Temperature : 60±2℃ Contact Resistance 2006.08.07 DSN K.M.S NO. ITEMS TEST CONDITIONS PERFORMANCE (1) Temperature : -30±2℃ Contact Resistance 2.3.1 Cold test (2) Duration of test : 96 hours : 200mΩ max. (3) Take off a drop water No. 2.1.2 to 2.1.4 & 2.2.1 (4) Standard conditions after test : 1 hour to 2.2.2 shall be satisfied. (1) Temperature : 80±2℃ Contact Resistance 2.3.2 Heat test (2) Duration of test : 96 hours : 200mΩ max. (3) Standard conditions after test : 1 hour No. 2.1.2 to 2.1.4 & 2.2.1 to 2.2.2 shall be satisfied. (1) Test cycles : 5 cycles (2) Standard conditions after test : 1 hour (3) 1 cycle Contact Resistance 2.3.3 Temperature Cycle : 200mΩ max. No. 2.1.2 to 2.1.4 & 2.2.1 to 2.2.2 shall be satisfied. MODEL TACT SWITCH SPECIFICATION DATE 3 OF 4MODEL No. DJT 1102 PAGE PAGE 5 / 6 APP K.Y.I CHK M.K.J 60℃ -10℃ 2h 1h 2h 1h PQS-1001-10(REV.0) DAEJIN INDUSTRY CO., LTD A4(210×297) 3.1 Auto soldering conditions 1) After switches were soldered, please be careful not to clean switches with solvent. 2) In the case of using soldering iron, soldering conditions shall be 280℃ max. and 3 sec max. 3) After switches were soldered, please be careful not to load the knobs of switchs. 3.2 Manual soldering conditions Temperature : 350 ± 5℃ Time : 3 sec max. 1) Please keep the received products under conditions of not high temperature, no high humidity and no direct-rays of the and no corrosive gases. 2) Our products are strongly recommended to use off within 3 months and are guaranteed the quality for 6 months of maximum period after receiving the products. 3) Please put some desiccants after opening off a vinyl pack in order not to enter the damp air and keep the products at the same place of the above-mentioned 4) Please be cautious not to give excessive load on the products. 5) Please be cautious not to keep the products with high pressure on the push buttons. Single sided copper-clad laminates. Time of immersion Within 5 sec Soldering number Within 2 time (But should bring down heat of the first soldering) CONDITION TACT SWITCH SPECIFICATION Temperature of solder 255℃ max. Printed wiring board 3. Soldering Preheat time 60 sec max. Area of flux 1/2 max. of P.W.B thickness ITEM DSN CHK APP PAGE 6 / 6 Preheat temperature 110℃ max. (Environmental temperature of soldering surface of P.W.B) MODEL No. DJT 1102 PAGE 4 OF 4 K.M.S M.K.J DATE 2006.08.07 4. Safety Keeping Condition K.Y.I MODEL PQS-1001-10(REV.0) DAEJIN INDUSTRY CO., LTD A4(210×297)