FCC报告模板

Report No.: GTE11071032 1 TEST REPORT Applicant Name & Address : Specialized Mesenger Services 836 Jury Court,Suite 10 San Jose, CA 95112,USA Manufacturer Name & Address : Foshan Shunde Loskon Electric Co.,ltd No.22 Renmin Road Lunjiao,Shunde,Foshan Product : Power Amplifier Model No. : R-70a,R-80,R-1050 Electrical Rating : AC120V,60Hz COUNTRY OF ORIGIN : CHINA Date Received : 2011-10-17 Date Test Conducted : 2011-10-17 to 2011-10-21 Test standards : FCC Part 15,Class B: 2009 Test Result : Pass Conclusion : The submitted samples complied with the above rules/standards. Remark : Part number: 153633.001 ***************************************End of Page*************************************** Prepared and Checked By: Approved By: _______________________ Signature Fvan Tu StevenZhou Engineer Team Leader GTS Guangzhou GTS Guangzhou 2011-10-21 Date This report is for the exclusive use of GTS's Client and is provided pursuant to the agreement between GTS and its Client. GTS's responsibility and liability are limited to the terms and conditions of the agreement. GTS assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the GTS name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by GTS. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an GTS certification program. The test report only allows to be revised within three years from its original issued date unless further standard or the requirement was noticed. General Testing Services Co.,Ltd 5F-20 of Xiangpu Building, XiangpuStreet, DongpuTown, Guangzhou City, Guangdong, China Tel / Fax: 86-20-6235 9071/86-20-2222 7157 Report No.: GTE11071032 CONTENT TEST REPORT (1) CONTENT (2) 1TEST RESULTS SUMMARY (3) 2TEST RESULTS CONCLUSION (4) 3LABORATORY MEASUREMENTS (5) 4TEST RESULTS (6) 4.1C ONDUCTED E MISSION T EST (6) 4.1.1Used Test Equipment (6) 4.1.2Block Diagram of Test Setup (6) 4.1.3Test Setup and Procedure (6) 4.1.4Test Data (7) 4.1.5Test Curve (8) 4.2R ADIATED E MISSION (10) 4.2.1Used Test Equipment (10) 4.2.2Block Diagram of Test Setup (10) 4.2.3Test Setup and Procedure (11) 4.2.4Test Data (11) 4.2.5Test Curve (12) 4.2.6Measurement uncertainty (12) 5APPENDIX I - PHOTOS OF TEST SETUP (13) 6APPENDIX Ⅱ - PHOTOS OF EUT (14) Report No.: GTE11071032 1TEST RESULTS SUMMARY Remark: 1. When determining the test results, measurement uncertainty of tests has been considered. 2. When determining the test results, measurement uncertainty of tests has been considered. Report No.: GTE11071032 2Test Results Conclusion (with Justification) RE: EMC Testing Pursuant to FCC Part 15, Class B: 2009 Performed On the Power Amplifier, Models:R-70a We tested the Power Amplifier, Model: R-70a to determine if it was in compliance with the relevant FCC rules as marked on the Test Results Summary. We found that the unit met the requirement of FCC Part 15, Class B: 2009 when tested as received. The worst case’s test data was presented in this test report. Radiated emission was tested in General Testing Services. Conclusion: The sample as received complied with the FCC Part 15 requirement. The test results of digital device portion in FCC test report are deemed satisfactory evidence of compliance with Industry Canada Interference – Causing Equipment Standard ICES-003. The production units are required to conform to the initial sample as received when the units are placed on the market. Report No.: GTE11071032 5 3 LABORATORY MEASUREMENTS Configuration Information Equipment Under Test (EUT): CUTTLEFISH Model : R-70a Serial No. Not Labelled Support Equipment : N/A Rated Voltage: AC120V Condition of Environment: Temperature : 15~35 C Relative Humidity: 35~60% Atmosphere Pressure 86~106kPa Notes: 1. EUT Grounding The unit was grounded as normally used. 2. Test Environment If ambient levels of emissions exceed the appropriate limit, the following steps were taken to assure compliance. First, the measurement bandwidth was reduced, if this did not affect the peak readings. Such a reduction can allow much closer examination of emissions close to local ambient signals. Second, the antenna could be brought closer to the EUT. Finally, in severe cases, testing was re-performed at night or other times when the offending signal was off the air. The measurements were made at nominal room temperature (25o C ± 10o C). 3. Test Site Conducted Emission test was done in Shielding Room of GTS. Radiated Emission test was subcontracted and was done in 3 m semi-anechoic chamber. 4. Test Platform Radiated emission test was made on 0.8m high, 1m x 1.5m wide non-conductive platform. Conducted emission test was made on 0.4m high non-metallic table above earthed ground plane (Ground Reference Plane). The EUT keeps a distance of at least 0.8m from any other of the metallic surface. 5. Measurement Uncertainty When determining of the test conclusion, the Measurement Uncertainty of test has been considered.