插座尺寸和高度

插座尺寸和高度 空调插1800mm-2000mm 落地的空调是350mm-500mm 普通插座和弱电插座300mm-350mm，并且间距为300mm。 而厨卫插座1500mm， 浴霸插座2100mm， 抽油烟机插座为1800mm。 开关高度一般为1300~1400mm。距门框边150mm-200mm 卫生间的热水器2.3m。 室内设计尺寸 工地 1、标准红砖23*11*6; 标准入户门洞0.9米*2米， 房间门洞0.9米*2米， 厨房门洞0.8米*2米， 卫生间门洞0.7米*2米， 标准水泥50kg/袋。 厨房 1.吊柜和操作台之间的距离60厘米。 2.在厨房两面相对的墙边都摆放各种家具和电器的情况下，中间应该留多大的距离才不会影响在厨房里做家务,120厘米。 为了能方便地打开两边家具的柜门，就一定要保证至少留出这样的距离150厘米。 3.要想舒服地坐在早餐桌的周围，凳子的合适高度80厘米。 对于一张高110厘米的早餐桌来说，这是摆在它周围凳子的理想高度。因为在桌面和凳子之间还需要30厘米的空间来容下双腿。 4.吊柜应该装高145至150厘米。 在餐厅 1.一个供六个人使用的餐桌120厘米。 这是对圆形餐桌的直径140*70厘米。 2.餐桌离墙应该远80厘米。 3.一张以对角线对墙的正方形桌子所占的面积要有多大, 180*180平方厘米 这是一张边长90厘米，桌角离墙面最近距离为40厘米的正方形桌子所占的最小面积。- than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and 4.桌子的标准高度72厘米。而椅子是通常高度为45厘米。 5.一张供六个人使用的桌子摆起居室里要占面积300*300厘米。 需要为直径120厘米的桌子留出空地，同时还要为在桌子四周就餐的人留出活动空间。这个方案适合于那种大客厅，面积至少达到600*350厘米。 6.吊灯和桌面之间最合适的距离70厘米。 卫生间 1(卫生间里的用具要占多大地方, 马桶所占的一般面积:37厘米×60厘米 悬挂式或圆柱式盥洗池可能占用的面积:70厘米×60厘米 正方形淋浴间的面积:80厘米×80厘米 浴缸的标准面积:160厘米×70厘米 2(浴缸与对面的墙之间的距离100厘米远。总之浴缸和其他墙面或物品之间至少要有60厘米的距离。 3(安装一个盥洗池，并能方便地使用，需要的空间是多大, 90厘米×105厘米。这个尺寸适用于中等大小的盥洗池，并能容下另一个人在旁边洗漱。 4(两个洗手洁具之间应该预留多少距离, 20厘米。这个距离包括马桶和盥洗池之间，或者洁具和墙壁之间的距离。 5(相对摆放的澡盆和马桶之间应该保持多远距离, 60厘米。这是能从中间通过的最小距离，所以一个能相向摆放的澡盆和马桶的洗手间应该至少有180厘米宽。 6(要想在里侧墙边安装下一个浴缸的话，洗手间至少应该有多宽, 180厘米。这个距离对于传统浴缸来说是非常合适的。如果浴室比较窄的话，就要考虑安装小型的带座位的浴缸了。 7(镜子应该装多高, 135厘米。这个高度可以使镜子正对着人的脸。 卧室 1 双人主卧室的最标准面积12平方米 夫妻二人的卧室不能比这个在小了。在房间里除了床以外，还可以放一个双开门的衣柜(120*60厘米)和两个床头柜。在一个3*4.5米的房间里可以放更大一点的衣柜;或者选择小一点的双人床，再在抽屉和写字台之间选择其一。就可以在摆放衣柜的地方选择一个带更衣间的衣柜。 2 如果把床斜放在角落里，要留出多大空间, 360*360厘米 这是适合于较大卧室的摆放方法，可以根据床头后面墙角空地的大小在拜访一个储物柜。 3 两张并排摆放的床之间的距离应该有多远, 90厘米 than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and 两张床之间除了能放下两个床头柜以外，还应该能让两个人自由走动。当然床的外侧也不例外，这样才能方便的清洁地板和整理床上用品。 4 如果衣柜被放在了与床相对的墙边，那么两件家具这间的距离应该是多少, 90厘米 这个距离是为了能方便地打开柜门而不至于被绊倒在床上 5 衣柜高240厘米 这个尺寸考虑到了在衣柜里能放下长一些的衣物(160厘米)，并在上部留出了放换季衣物的空间(80厘米) 6 要想容的下双人床、两个床头柜外加衣柜的侧面的话，一面墙应该有多大, 420*420厘米 这个尺寸的墙面可以放下一张160厘米宽的双人床，和侧面宽度为60厘米的衣柜，还包括床两侧的活动空间(两侧60——70厘米)，以及柜门打开时所占用的空间(60厘米)。如果衣柜采用拉门，那么墙面只需要360厘米宽就够了 客厅 1.长沙发与摆在它面前的茶几之间的正确距离是多少, 30厘米 在一个(240*90*75高 厘米)的长沙发面前摆放一个(130*70*45高 厘米)的长方形茶几是非常舒适的。两者之间的理想距离应该是能允许你一个人通过的同时又便于使用，也就是说不用站起来就可以方便地拿到桌上的杯子或者杂志。 2.一个能摆放电视机的大型组合柜的最小尺寸应该是多少, 200*50*180高 厘米 这种类型的家具一般都是由大小不同的方格组成，高处部分比较适合用来摆放书籍，柜体厚度至少保持30厘米;而低处用于摆放电视的柜体厚度至少保持50厘米。同时组合柜整体的高度和横宽还要考虑与墙壁的面积相协调。 3.如果摆放可容纳三、四个人的沙发，那么应该选择多大的茶几来搭配呢, 140*70*45高 厘米 在沙发的体积很大或是两个长沙发摆在一起的情况下，矮茶几就是很好的选择，高度最好和沙发坐垫的位置持平。 4.在扶手沙发和电视机之间应该预留多大的距离, 3米 这里所指的是在一个25英寸的电视与扶手沙发或长沙发之间最短的距离。此外，摆放电视机的柜面高度应该在40厘米到120厘米之间，这样才能使观众保持正确的坐姿。 5.摆在沙发边上茶几的理想尺寸是多少, 方形:70*70*60高 厘米。 椭圆形:70*60高 厘米。 放在沙发边上的咖啡桌应该有一个不是特别大的桌面，但要选那种较高的类型，这样即使坐着的时候也能方便舒适地取到桌上的东西。 6.两个面对面放着的沙发和摆放在中间的茶几一共需要占据多大的空间, than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and 两个双人沙发(规格 160*90*80高 厘米)和茶几(规格 100*60*45高 厘米)之间应相距30厘米。 7.长沙发或是扶手沙发的的靠背应该有多高, 85至90厘米。 这样的高度可以将头完全放在靠背上，让您的颈部得到充分的放松。如果沙发的靠背和扶手过低，建议您增加一个靠垫来获得舒适。如果空间不是特别宽敞，沙发应该尽量靠墙摆放。 8.如果客厅位于房间的中央，后面想要留出一个走道空间，这个走道应该有多宽, 100至120厘米。 走道的空间应该能让两个成年人迎面走过而不至于相撞，通常给每个人留出60厘米的宽度。 9.两个对角摆放的长沙发，它们之间的最小距离应该是多少, 10厘米。 如果不需要留出走道的话，这种情况就能允许您再放一个茶几了。 家具设计的基本尺寸 (单位:厘米) 衣橱:深度:一般60~65;推拉门:70，衣橱门宽度:40~65 推拉门:75~150，高度:190~240 矮柜: 深度:35~45，柜门宽度:30-60 电视柜:深度:45-60，高度:60-70 120;长度:180，186，200，210 单人床:宽度:90，105， 双人床:宽度:135，150，180;长度180，186，200，210 圆床: 直径:186，212.5，242.4(常用) 室内门:宽度:80-95，医院120;高度:190，200，210，220，240 窗帘盒:高度:12-18;深度:单层布12;双层布16-18(实际尺寸) 沙发:单人式:长度:80-95，深度:85-90;坐垫高:35-42;背高:70-90 双人式:长度:126-150;深度:80-90 三人式:长度:175-196;深度:80-90 四人式:长度:232-252;深度80-90 茶几:小型，长方形:长度60-75，宽度45-60，高度38-50(38最佳) 中型，长方形:长度120-135;宽度38-50或者60-75 正方形: 长度75-90，高度43-50 大型，长方形:长度150-180，宽度60-80，高度33-42(33最佳) 圆形:直径75，90，105，120;高度:33-42 方形:宽度90，105，120，135，150;高度33-42 书桌:固定式:深度45-70(60最佳)，高度75 活动式:深度65-80，高度75-78 than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and 书桌下缘离地至少58;长度:最少90(150-180最佳) 餐桌:高度75-78(一般)，西式高度68-72，一般方桌宽度120，90，75; 长方桌宽度80，90，105，120;长度150，165，180，210，240 圆桌:直径90，120，135，150，180 书架:深度25-40(每一格)，长度:60-120;下大上小型下方深度35-45，高度80-90- 活动未及顶高柜:深度45，高度180-200 木隔间墙厚:6-10;内角材排距:长度(45-60)*90 室内常用尺寸: 1、墙面尺寸 (1)踢脚板高;80—200mm。 (2)墙裙高:800—1500mm。 (3)挂镜线高:1600—1800(画中心距地面高度)mm。 2(餐厅 (1) 餐桌高:750—790mm。 (2) 餐椅高;450—500mm。 (3) 圆桌直径:二人500mm(二人800mm，四人900mm，五人1100mm，六人1100-1250mm，八人1300mm，十人l500mm，十二人1800mm。 (4) 方餐桌尺寸:二人700×850(mm)，四人1350×850(mm)，八人2250×850(mm)，- (5) 餐桌转盘直径;700—800mm。 餐桌间距:(其中座椅占500mm)应大于500mm。 (7) 主通道宽:1200—1300mm。 内部工作道宽:600—900mm。 (9) 酒吧台高:900—l050mm，宽500mm。 (10) 酒吧凳高;600一750mm。 家庭装修水路改造常用参考尺寸数据(尺寸以毛坏未处理墙地数据为准)常见预留尺寸供参考: 一: 1.台盆进水口 50-55CM(离地) 2.洗菜盆进水口 40-50CM(离地) 3.拖把池进水口 75-80CM(离地) 4.洗衣机进水口 120CM(离地) 5.电热水器进水口 170CM(离地) 6.燃气热水器进水口 130CM(离地) 7.淋浴龙头进水口 110CM(离地) 8.淋浴龙头冷热进水口左右管距 14.5--15CM 9.坐厕进水口 20CM(离地) 10.坐厕排水口 30--32CM(离墙) than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and 11.净身器排水口 26--30CM(离墙) 二: 1、淋浴混水器冷热水管桩头中心间距150MM,桩头距地1050-1200MM;冷热水出口必须平行 2、上翻盖洗衣机水口高度1250MM; 拖把池桩头高度低200mm高800mm. 3、电热水器桩头高度1700MM、桩头直径-200MM; 4、马桶给水口距地200MM,距马桶后中心一般靠左250MM: 5、燃气热水器、距地 桩头高1400MM一1500MM、宽200MM 6、立柱盆的冷热水 桩头离地高度为550—500MM，下水道一定安装在立柱内，台盆下水管埋入墙内， 7、 厨房洗菜盆进水口离地450MM。——500MM 8、卫生间排污管用110MM PUC管，下水管用50—75MM PUC管， 9、马桶后下水管一般坐厕中心离墙280—300MM，前下水一般坐厕中心离墙400-420mm、地漏口离墙200MM 10、安装浴缸前应检查防水是否完整，如无防水或防水破坏，须重做防水并高出浴缸100MM。 11、淋缸上的混合龙头的左右位置一定要安装在浴盆中间(先确定浴缸尺寸)，桩头高为1200MM。中650MM。低250MM。间距150MM 12、坐便器的进水出口尽量安置在能被坐便器挡住视线的地方。连体坐便器要根据型号来确定出水口的位置，一般要留在马桶下水口正中左方250 MM处。 13、淋浴混水阀的左右位置正确,且装在浴缸中间(先确定浴缸尺寸),高度为浴缸上中150-200mm，按摩浴缸根据型号进行出水口预留。混水阀孔距一般保持在(暗装)150mm，，连杆式淋浴器要根据房高和业主个人需要来确定出水口位置。 14、 浴室防水层应该不低于1.8米. 15、洗脸盆PPRΦ32-50，洗菜池PPRΦ40-50。 16、太阳能水阀高度1100MM一2000MM 宽度150MM、上桩头放在顶上、另外再用PPR做一个出水管与埋在墙内、上桩头出顶、下桩头距地200MM小厨宝桩头、净水器桩头要放在橱柜里高距地300MM。 室内家具标准尺寸表(单位:厘米) 衣橱:深度:一般60~65;推拉门:70，衣橱门宽度:40~65 推拉门:75~150，高度:190~240 矮柜: 深度:35~45，柜门宽度:30-60 电视柜:深度:45-60，高度:60-70 单人床:宽度:90，105，120;长度:180，186，200，210 双人床:宽度:135，150，180;长度180，186，200，210 圆床: 直径:186，212.5，242.4(常用) 室内门:宽度:80-95，医院120;高度:190，200，210，220，240 厕所、厨房门:宽度:80，90;高度:190，200，210 than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and 窗帘盒:高度:12-18;深度:单层布12;双层布16-18(实际尺寸) 沙发:单人式:长度:80-95，深度:85-90;坐垫高:35-42;背高:70-90 双人式:长度:126-150;深度:80-90 三人式:长度:175-196;深度:80-90 四人式:长度:232-252;深度80-90 茶几:小型，长方形:长度60-75，宽度45-60，高度38-50(38最佳) 中型，长方形:长度120-135;宽度38-50或者60-75 正方形: 长度75-90，高度43-50 大型，长方形:长度150-180，宽度60-80，高度33-42(33最佳) 圆形:直径75，90，105，120;高度:33-42 方形:宽度90，105，120，135，150;高度33-42 书桌:固定式:深度45-70(60最佳)，高度75 活动式:深度65-80，高度75-78 书桌下缘离地至少58;长度:最少90(150-180最佳) 餐桌:高度75-78(一般)，西式高度68-72，一般方桌宽度120，90，75; 长方桌宽度80，90，105，120;长度150，165，180，210，240 圆桌:直径90，120，135，150，180 书架:深度25-40(每一格)，长度:60-120;下大上小型下方深度35-45，高度80-90 活动未及顶高柜:深度45，高度180-200 木隔间墙厚:6-10;内角材排距:长度(45-60)*90 室内常用尺寸: 1、墙面尺寸 (1)踢脚板高;80—200mm。 (2)墙裙高:800—1500mm。 (3)挂镜线高:1600—1800(画中心距地面高度)mm。 2(餐厅 (1) 餐桌高:750—790mm。 (2) 餐椅高;450—500mm。 (3) 圆桌直径:二人500mm(二人800mm，四人900mm，五人1100mm，六人1100-1250mm，八人1300mm，十人l500mm，十二人1800mm。 (4) 方餐桌尺寸:二人700×850(mm)，四人1350×850(mm)，八人2250×850(mm)， (5) 餐桌转盘直径;700—800mm。 (6) 餐桌间距:(其中座椅占500mm)应大于500mm。 (7) 主通道宽:1200—1300mm。 (8) 内部工作道宽:600—900mm。 (9) 酒吧台高:900—l050mm，宽500mm。 (10) 酒吧凳高;600一750mm。 3(商场营业厅 than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and (1)单边双人走道宽:1600mm。 (2)双边双人走道宽:2000mm。 (3)双边三人走道宽:2300mm。 (4)双边四人走道宽;3000mm。 (5)营业员柜台走道宽:800mm。 (6)营业员货柜台:厚600mm，高:800—l 000mm。 (7)单*背立货架:厚300—500mm，高:1800—2300mm。 (8)双*背立货架;厚;600—800mm，高:1800—2300mm (9)小商品橱窗:厚:500—800mm，高:400—1200mm。 (10)陈列地台高:400—800mm。 (11)敞开式货架:400—600mm。 (12)放射式售货架:直径2000mm。 (13)收款台:长:1600mm，宽:600mm 4(饭店客房 (1)标准面积:大:25平方米，中:16—18平方米，小:16平方米。 (2)床:高:400—450mm，床*高:850—950mm。 (3)床头柜:高500—700mm;宽:500—800mm。 (4)写字台:长;1100—1500mm;宽450—600mml高700—750mm。 (5)行李台，长9l0—1070mm宽500mm高400mm。 (6)衣柜:宽:800—1200mm高1600—2000mm深500mm。 (7)沙发:宽:600一800mm高:350—400mm*背高1000mm (8)衣架高:1700—1900mm。 5(卫生间 (1)卫生间面积;3—5平方米。 (2)浴缸长度;一般有三种1220、1520、1680mm;宽;720mm，高450mm。 (3)坐便;750×350(mm)。 (4)冲洗器:690×350(mm)。 (5)盟洗盆:550×410(mm)。 (6)淋浴器高:2100mm。 (7)化妆台;长:1350mm;宽450 mm。 6(会议室 (1)中心会议室客容量:会议桌边长600(mm)。 (2)环式高级会议室客容量;环形内线长700—l 000mm。 (3)环式会议室服务通道宽:600—800mm。 7(交通空间 (1)楼梯间休息平台净空:等于或大于2100mm。 (2)楼梯跑道净空:等于或大于2300mm。 (3)客房走廊高;等于或大于2400mm。 than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and (4)两侧设座的综合式走廊宽度等于或大于2500mm。 (5)楼梯扶手高;850—1100mm。 (6)门的常用尺寸:宽:850—1000mm。 (7)宙的常用尺寸;宽;400—1800mm，(不包括组合式窗子) (8)窗台高;800—1200mm。 8(灯具 (1)大吊灯最小高度:2400mm。 (2)壁灯高:1500—1800mm。 (3)反光灯槽最小直径:等于或大于灯管直径两倍。 (4)壁式床头灯高:1200—1400mm。 (5)照明开关高:1000mm。 9(办公家具 (1)办公桌:长:1200—1600mm:宽:500—650mm 5高;700—800mm。 (2)办公椅:高;400—450mm长×宽:450×450(mm)。 (3)沙发:宽:600—800mm;高:350—400mm;*背面:1000mm。 (4)茶几;前置型:900×400×400(高)( mm);中心型:900x 900×400(mm)、 700×700×400(mm);左右型:600×400×400(mm)。 (5)书柜:高:1800mm，宽:1200—1500mm;深:450—500mm。 (6)书架:高:1800mm 6宽:1000—1300mm ;深:350—450mm 追问 有厨房橱柜的高度么, 回答 一般是85，如果身高高么可以适当提高到90~95，但是煤气灶部分可以适当降下来 than ? 5mm; elevation deviation was less than ? 5mm work surface height difference is not more than 3mm on the one end to the other end; wrong tooth at the joint is less than 1mm. Side rail mounting: side rail installation take each side rail on two points. During the installation process, use tensioner to adjust the side rail. Side rail hole top center within the scope of the work is less than +2~-1mm, scope of work at a 4-to-2; wrong tooth less than 1mm at the joint work surface flatness 2mm lateral curvature RADIUS is less than ? 5mm sealing plate surface distortion is less than 1mm. Reinforcement process of adjustment is completed, in order to prevent tank deformation or displacement, welded tank side of the door, then welded reinforcing side, lap length is not less than 100mm. Door installation: the lintel the installation focuses on family Center sill plane distance h is less than ? 3mm; work surface flatness of less than 2mm; combination of surface dislocation is less than 0.5mm surface distortion is less than 1.5mm. Mode with the side rail. Grid slot bi-directional gate leaf on a car lift and lower grille blade adjustment is completed with pin connection, then try connecting rod. After you check the accessories complete the fastening, hanging out the bottom opening and closing test in still water as a whole. 8.2.3 tainter and hinge installation Setup: Pivot fixed bearing installation ? orbit stitching, alignment ? arm splicing, installation connected with the headstock ? ? ? welding door leaf side connecting plates welded, water seal installation ? clean, and wipe off. 8.2.3.1 hinge installation and