新车购买的注意事项

新车购买的注意事项 一、看车: 1、我是上帝，我是来买车的，别显得很客气，让销售商觉得好骗好欺负。 2、买车前讲价时注意加发动机护板，能叫送就送，不送花钱也要买。 3、要求看现货车，最好是别人订的，但还没有去开的。这样才能看出销售商的信誉和所订车的质量。 4、试驾:车子不是看的，是跑的。所以，推荐大家在决定前，进行试驾还是很有必要的，首先发动车，调整左右后视镜，系安全带，起步上路后，应感觉方向灵活，路感平稳，在中低速下松开方向盘，500米距离内偏离原行驶方向不超过5米为正常偏移。手动挡挡位轻松无晦涩感，自动挡换挡无明显冲击感为正常。有意寻找不平路面行驶一下，车内应无杂音异常。过弯后方向盘自动回正。新车油门略有迟钝为正常，但过了迟钝点应该加速畅快。开空调压缩机，油门无明显增加负担，且应当在10秒钟内感到出风口的凉意。 二、买车: 1、买现货车给订金前记得抄下所订车发动机号码，小心销售者用翻新车(试驾车)换车。 2、买车时要在或附加上注明交车日期(适用于订货车)、车身颜色。如有要求送配件也要在上面注明品牌、型号、数量。 三、提车: 1、提车时注意看里程公里读数:一般为8——10公里，看水箱散热片有无杂物、座位保护包装及车头塑料纸是否完整、车内乘驾位及仪表等是否有污秽物。 2、提订货车时，要注意看出厂日期和提货日期是否相距太长时间，如相距时间过长，此车有可能为展示车(放在展览大厅供客人展览)或翻新车(试驾车)。 3、提车时记得索要生产日期和运输日期，详细比对所提车辆。 4、买车后，车交给4S店销售办牌和各种手续，记得抄里程表，不要让销售开着车满大街溜车。 5、看外观:挑选新车，可要求两台同型号车挑选。注意车身缝隙和漆面。这样的观察有技巧的，可以着重观察保险杠和车身缝隙，车门缝隙和前后保险杠缝隙，打开车门观察内外油漆是否无色差等。对于漆面，则对外界光线条件的要求比较高。最好的观察光线是日光下，什么问题都不能掩盖。如果是在展厅选车，可以斜对着日光方向观察，也能起到同样的效果。合格的漆面应当平整无桔皮水波纹瑕疵，保险杠和车身、车门外边缘、左右外后视镜等易受1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 损部位无色差。对于金属漆和珠光漆还可以通过观察漆内铝粉或云母颗粒的均匀程度辅助判断。上面的程序进行完了，这车的外观算是合格了。 6、看机械部分:最先当然是看发动机了，工作良好的发动机应该是外观无油渍，启动时反应迅速灵敏，运行时平稳不抖动，声音平顺，没有尖利的杂音或非固定频率的噪音。冷车状态怠速略高，看转速表约1000转左右。水温上升后，怠速下降至780转左右，此时轻加油，感觉应该反应敏捷，无爆震音或松旷音。用手摸发动机盖，无明显震动，坐进车内，基本听不到发动机工作噪音。如果对以上方面心里没底，也可以通过两部同时运转的发动机进行横向比较，也是一种好办法。发动机加机油的部位应该干净无油渍，即使没有明显油渍，有粘灰尘的情况也等同这点，因为只有粘油的部位才会粘灰尘的。对于其他机械部件，也可以用这种办法辅助判断。检查好发动机的三油两液(三油:机油，刹车油，方向助力油。两液:冷却液，风窗清洗液)的液面高度，接下来就是检查电瓶了。新车可以通过观察电瓶状态指示了解电瓶的状态，如果是绿色指示，表示电瓶状态良好且蓄电充足，如果是黑色或白色，则表明蓄电不足甚至已损坏，最好尽快充电。 7、看地面:看完了发动机，不妨低身看一看运行一段后的车下地面。看看有无水油渍的迹象，对于判断一些隐性故障还是有帮助的。正常的情况是除了排气管有水滴落外，其他部位应该没有任何水油渗漏的。 8、看轮胎:正常的新车轮胎应该胎壁无任何损伤，特别是前轮胎壁。胎面无钉扎痕迹，前后轮胎胎毛健在的最好，至少后轮的胎毛应该能看到，如果四轮光光，没有半根胎毛，且本地路面不差，就要三思了。 9、看车门:合格的车门应该开关用力均匀，无异响。密闭橡胶完好，关门可以感觉到明显的密闭效果，且车门在最后一段行程会有类似于吸力的力量将车门关闭。车门框下边缘漆面完好无损，如果发现磨损或污浊，就要考虑这车的储存情况是否理想了。电动玻璃为四门防夹设计。 10、看内饰:内饰没别的，洁净第一。内饰应该洁净，特别是易脏的部分，如内拉手和内饰灯周围。电动部分或机械部分应当轻便灵活，运行无杂音。车厢地面干净无水渍。检查车内灯光，应该工作正常完好。现场去除座椅包装白套，检查原厂真皮座套是否有恙，水杯架和眼镜盒盖这些易受损的部件应试用几下，保证功能完好。当然，还有别的很多注意事项，这里就不一一说明了 四、付款方面 您如果是现款提车，需要的只是带好您的身份证，还有购车款。手续相对简单。如果您想“用明天的钱来享受今天的生活”贷款购车的话，您还需要提前办理相关手续。 办理汽车贷款一般的流程:咨询? 决定购买? 准备资料、填写表格? 提交资料? 初审? 交银行复审批准? 交首付款? 选车? 签购车合同? 提车? 办理相关手续? 开车回家?每月还款。 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; ?注意:放贷给您的银行还会对您的情况进行审核。审核通过贷款的办理一般在一周时间左右。您办理好了贷款就可以去经销商那里购买自己的爱车了，全款购车除了贷款的环节，其他过程与贷款购车相同。 五、“定金”与“订金” 您如果购买的车型经销商那里有现车，您办完各项手续后就可以开走了。但是如果购买某些紧俏车型，经销商处没有现车，往往还需要预订。通常需要同经销商签订一份《购车意向书》，并缴纳一定数量的定金(或订金)。然后，经销商将向汽车生产厂预订车型，并按照消费者的购车号安排交车时间，因车型的不同，少则几天多的时候能达到数月。 在这里您需要注意的是:“定金”与“订金”是截然不同的两个概念。 如果您在和经销商签订《购车意向书》时交了“定金”就意味着您所定车型将不能更换或退还。因为生产厂家采取实名购车制进行订单管理，规定只能“一单一车”，而且不能更改购车人姓名。 如果您在车型的选择上还是犹豫不决，劝您还是先交一部分“订金”为好。为了防止出现问题，应当以书面形式将补充相应的约定列入合同之中。订金目前法律上没有明确规定，一般可理解为“预付款”，一方违约时，双方有约定的按照约定执行;如果无约定，经营者违约时，应无条件退款。 六、工薪族买车的八大要诀 贷款消费并不意味超前消费，只是因人而异设计的理财方式而已。它首先是以自身实力为前提，否则最后不仅透支金钱还透支信誉，那可就没救了。 (1)车辆的价位最好别超过家庭两年的收入。 (2)买车别攀比，因为金钱有限，好车无限。 (3)强劲的发动机在现阶段任何大城市的城区都无用武之地。 (4)如果不是成熟车型，新推的车型应缓买。 (5)家庭购车一定要考虑空间。 (6)无用的功能和花哨的设施只会增加成本和出毛病的几率。 (7)任何时候，对车的新鲜感不会超过三个月。 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; (8)选购刚刚降价的车辆会相对减少损失。 易车网为你解答 一、选车: 我们有了买车的想法后，买什么车呢,多少钱的车呢,心中有个数。下面是选车全攻略基本步骤: 选车步骤一.买车的预算 确定价位:5万、5-10万、10-15万、15-20万、 20-30万、30万-50万、50万以上 选车步骤二.确定车辆的用途与样式: (1)选轿车/SUV/跑车/休旅车/MPV/商务车/微型车, 1、SUV:视野开阔，够气势;SUV一般有城市越野车(如CR-V)与越野车(Jeep)。 2、跑车:开在路上抢眼球，适合个人使用。 3、休旅车:房车，转为家庭设计的野外使用的汽车; 4、>MPV:空间非常大，适合载货、经常搭载多人; 5、商务车:适合接待用车，搭载多人空间大。 6、微型车:适合>城市个人代步，价格便宜，方便泊车。 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 根据个人的用途，我们可以选择不同的汽车样式。当然，更多的一般是选择一般家轿。确定车型后，我们可以根据预算，在网上海量挑选个品牌的车型。 (2)选三厢还是两厢车,三厢比两厢多个尾箱。一般说来三厢车的后备厢的容积会比两厢大，但是两厢车把后排坐位放倒就可以获的一个比3厢车大的多的载物空间，两厢车可以轻松的装下一台29寸的电视机，三厢车就不行。两厢半综合了两厢与三厢的优点，但是密封性不如三厢。选择厢式这个选车一个重点，还要凭借个人喜好来进行。十万元包牌价范围可选择的车型有半数是三厢;两厢车大多数来自于合资品牌的精典两厢车，车型系列已有畅销纪录，产品已进入成熟期，如206、派力奥、雨燕等;而在这一价格区间的三厢车则以自主品牌的低配车型为主，车型系列比较年轻，如比亚迪F3、奇瑞A520等。 三厢车与两厢车价格方面有没有很大的区别,没有，三厢车与两厢车基本纯粹就是个人喜好问题，价格方面不会有特别的差别。 选车步骤三.新车,成熟车型,二手车, 根据以上2步，我们大概可以筛选出一些范围了。现在的汽车出产速度特别快，我们应该选择最新的车型还是已经成熟的车型呢,还有二手车也是一个考虑方向。 一般来说，最新推出的车型，由于没有经常市场的验证，很可能会出现一些缺点和缺陷(汽车召回)，同时，汽车经销商抓住了消费者喜新厌旧的心理，总爱在推出新车型的时候说得如何好如何好。实际还是有待时间来考验。当然，已经成熟的车型是一个很不错的选择，市场是的维修配件也非常容易找到，由于已经出了几年，配件不会很贵，代表车型包括有捷达等。二手车，如果有相关熟悉汽车市场的人带着，挑一台好的二手车也是相当不错的选择。 选车步骤四:汽车品牌的选择 具体的品牌就不用细说了，如果有朋友有车，不妨听听他们的用车意见。下面说说各种车系生产的汽车都有什么特点: 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 日系车:省油经济，但动力性和质量稍差。做工比较细腻，价格较便宜，发动机排量通常不大，外观比较适合国人的审美观。 德系车:质量好，动力也很不错，技术过硬，就是比较贵物有所值嘛。外观显得朴素，价格也偏高。 美系车:动力强劲，耗油，质量不错，外型粗犷豪放，空间大是优势，比较注重安全性。 欧系车:法国、意大利、英国等的车型在设计和驾驶方面都让人感到有激情，注重安全性。 韩系车:靠近日系车，质量也算可以，价格相对便宜，但是缺乏太多亮点。 国内自主品牌:品牌众多，价格低廉，款式多样，经常有“抄袭”的样式出现，安全性较低。随着汽车技术的发展，自主品牌的质量得到了很大的提升，虽然还不能与德系对比，但其价格与质量来说，性格比很高。 选车步骤五.驾驶性能:手动档OR自动档车, 同一个车系有不同的车型不同的车款，不同的车款内部配置不同，有的手动档有的自动档，因此价格会有不同，而且自动档要比手动档的汽车更贵一点。车用变速器通俗来讲有手动、自动两种，但具体又分为手动变速器(MT)、自动变速器(AT)、手自动变速器(AMT)、手动/自动一体变速器、无级变速器CVT五类。除了买车成本便宜一些，在维修成本方面手动档几乎不需太多维修费用，而自动档变速器维修技术复杂，费用要高很多，而且手动挡也要相对省油的多。 选车步骤六.安全性的考虑 从安全性而言，我们将其分为主动安全性和被动安全性。人们经常会听到"ABS、ESP"等词汇，这些是防抱死制动系统，和动态稳定系统的缩写，以及，制动力辅助系统、制动力感载分配系统、防炫目后视镜，这些就是典型的主动安全配备，即:事故发生之前，就以某些手段，去避免事故的发生。此外，防滑踏板、高效率的制动系统、良好的机械响应能力、1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 良好的灯光系统、都可以归纳为主动安全装备，这些装备都可以从不同方面提高行车的主动安全性能。而安全气囊、可溃缩转向柱、安全带、碰撞吸能区等，皆为被动安全配备，也就是，在事故发生之后，来减小或避免事故所造成的危害。在国产车型中，各种安全配备，已经非常广泛的被使用。目前，所有的小型车都配备了三点式安全带、安全玻璃等配备。大部分的国产轿车都配备了 ABS和安全气囊。 选车步骤七.养车成本的考虑 这里包括了考虑油耗、维修成本、零件价格等，买车后的一切支出成本计算。用车是一个长时间的过程，购买用车成本低的汽车更换算，当然也可以通过驾车习惯等降低用车养车成本。 选车步骤八.保值率 现在的车市价格波动频繁，用车迅速贬值，购新车要先估算保值率，以免将来出售时赔钱赔得心疼。首次购车应尽可能购买成熟品牌的产品，而且该产品短期内不太可能停产。这类汽车由于售后服务网络健全，保有量大，车辆保值率相对较高，三五年内出售会有个好价钱。什么车最保值,看看大家的选择:买什么车最保值,你的车保值吗, 选车步骤九.排量与动力 为什么排量与动力放到较后的位置呢,现在的汽车动力方面基本没有问题，通常第一个选择用途的时候基本就能够确定大概的排量与动力了。通常这时候只需要在2种排量间选择即可。 选车步骤十.个人感觉舒适性 说那么多以后，看看汽车配置是否适合自己，赶快动身去4S试驾一下～试乘试驾、亲身体验;包括行车的舒适性和乘坐的舒适性。各汽车品牌全国4S店查询 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 以上选车十大注意实现基本可以在网上迅速查找到，不妨放下心来慢慢挑慢慢找，确定最好几款车型后，听听别人的用车心得，最后到4S店好好亲身试驾一下。 二、查店询价到店评车 选好车当然要问下价格，由于汽车厂商在全国各个区域的销售策略和营销成本不尽相同，导致有些区域的价格相对较高(比如一些二、三级县市区)，有些则相对较低(比如上海、北京)。因此消费者在去经销商4s店看车之前最好先查出该地区的所有4S店电话，然后逐个打电话询价，接着再确定去哪家看车。买车也要货比三家～四家～各汽车品牌全国4S店查询 查询价格这个动作，不一定是在买的时候才问，在试驾的时候就应该详细问问具体近期有没有优惠活动，价格的范围等等。 一般情况下，逢年过节，五一、十一等黄金周都是汽车促销的最佳时间，因此这时候价格有可能会更优惠，有耐心的消费者应该要等有实际优惠才出手。五一、十一降价的幅度也比较大，其它时间段购车在价格方面优惠的幅度不是很大。但是厂家在不断调整相关车型的价格，经销商也在推出一系列的促销活动，在其它时间段购车照样会得到实惠。 总之，任何时候购车都是正确的，因为您享受到了有车后的喜悦。 选好几个意向车型当然也要亲自去看看实车。建议您到厂家授权的4S店购车，因为在那里不仅可以亲眼目睹自己喜欢的爱车，看看外观和内饰听听专业销售人员的介绍，，带上驾驶证让自己对爱车有一个全面的了解。现在大部分经销商都提供“试乘试驾”服务您可以亲自体验和感觉一下车的动力和舒适性，和爱车来一个近距离的接触，看看和您心中的期待的表现是不是差不多，对您的选择是一个关键的参考。 另外，去4S店除了看车以外，还有必要做的事情就是考评下4S店的售后服务的软硬件服务设施。 三、确定车型付款购车 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 如果您一切都准备好了，就可以寻找合适的经销商购车了。现在有不少的购车团，车主可以先参加一次试试实际情况如何才决定是否要一起参加团购。通常团购能够得到更优惠的价格。 接着就是付款的问题了。 付款购车须注意一下几个问题: (1)付款方式: 现款，相对比较简单需要的只是您本人的身份证，还有购车款。 贷款，先要办理贷款手续。首付款总额=首付款+保险费用+牌证费用。 需要特别注意的是:一般首期付款额不得少于车价的40%，贷款额不得超过购车款的60%，私家车贷款期限最长不能超过5年～ 一般的流程: 咨询?决定购买?准备资料、填写表格?提交资料?初审?交银行复审批准?交首付款?选车?签购车合同?提车?办理相关手续?开车回家?每月还款 ?以下是办理汽车贷款的相关规定供您参考 办理个人汽车贷款相关规定 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 期间放贷给您的银行还会对您的情况进行审核。如果审核通过贷款的办理一般在一周时间左右。您办理好了贷款就可以去经销商那里购买自己的爱车了，全款购车除了贷款的环节其它过程与贷款购车相同。 (2)“定金”与“订金” 您如果购买的车型经销商那里有现车您办完各项手续后就可以开走了。但是如果购买某些紧俏车型，经销商处没有现车的时候，往往您还需要预订。通常需要同经销商签订一份《购车意向书》，并缴纳一定数量的定金(或订金)。依车型和经销商的情况不同，少则几百元几千元多则上万元。然后，经销商将向汽车生产厂预订车型，并按照消费者的购车号安排交车时间，因车型的不同少则几天多的时候能达到数月。如果经销商以种种原因不能按合同约定时间交车，您可以要求经销商双倍返还定金。车到后您需要交清余下全部车款后再提车。 在这里您需要注意的是:“定金”与“订金”是截然不同的两个概念。 如果您在和经销商签定《购车意向书》时交了“定金”就意味着您所定车型将不能更换或退还。因为生产厂家采取实名购车制进行订单管理，规定只能 “一单一车”，而且不能更改购车人姓名。除非您是铁定了要买这款车，如果您还是犹豫不决，还有其它的选择权您千万不要交“定金”。 定金:定金具有一种担保性质，一方违约时，双方有约定的按照约定执行;如果无约定，经营者违约时，“定金”双倍返还消费者;消费者违约时，“定金”将不予返还。 如果您在车型的选择上还是犹豫不决，劝您还是先交一部份“订金”为好。为了防止如果您在预订车型的过程中出现了其它问题导致您不能购买此车，应当以书面形式将补充相应的约定列入合同之中，而且越详尽越好。以减少不必要的麻烦～ 订金:目前法律上没有明确规定，一般可理解为“预付款”，一方违约时，双方有约定的按照约定执行;如果无约定，经营者违约时，应无条件退款;消费者违约时，可以协商解决并要求经营者退款。 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; (3)办理保险: 现在的保险公司的数量比较多，对于您来说选择余地比较大。各个保险公司的险种也是大不相同，怎样才能选择适合自己的车险呢,首先要考虑服务好、理赔迅速可以满足你实际需要的公司，建议不要一味的追求低价格，低价格可能意味着服务和对您基本保障范围上的缩水。在险种的选择上要根据您个人的情况而定，是不是“新手”、开车的习惯、车辆存放的地点是否安全、车上经常是几个人、当地路况怎么样等等。总之，一定要选择适合自己的公司和险种，这样您的钱才花到了“刀刃上”，也会减少日后的麻烦。 (4)发票工商验证 工商部门验证须有机动车统一发票第四联或调拨单。然后在发票上加盖验证章，进口车还需交验由经销商提供的海关货物进口证明、进出口检验检疫证明、如果购买罚没车的话需要海关提供罚没证明。 (5)交购置附加费: 购买新车必须到车辆购置附加费征稽管理处缴纳购置附加费。计算方法为:净车价?11.7。 (6)交纳车船使用税: 车主在投保交强险时就必须交车船税，否则保险公司就会拒绝办理交强险。具体征税标准，则由各省国税部门确定。 所需要的文件:购车发票、行驶证; 纳税时间:上牌一个月内; 纳税地点:各区、县地方税务机关;轿车每辆年税费为200元。 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; (7)到机动车检测场办理验车: 您须要携带以下文件: 1.车主个人身份证; 2.购车发票; 3.车辆保险保单; 4.车辆出厂合格证(进口车需出示海关货物进出口证明和进出口货物检验检疫证明) 验车费方面根据车型不同费用也有所出入。 (8)上牌:照相费30元，拓号费40元，移动证3元，牌照费154，环保卡3元，总计 230元，用户自己办理 (8)交纳养路费:轿车每月110元，其它车型请咨询当地养路费征稽所。 (9)办理行驶证:在车管所为车辆照相二张(正、侧面各1张)登记好相关资料，建立档案。 这些手续要您自己来办理是有点烦琐，现在不少经销商都能提供买车“一条龙服务”。您只要在经销商处选好车交好了该付的款项后，保险、验车上牌等一系列事情都由经销商来为您办理，免去了您来回奔波之苦。车管所还确定了几家有信誉的经销商可以发牌，将车牌号段分配给他们,您如果在这些指定经销商处购车后,可以在经销商处办妥理审核、验车、照相、选号、发牌、发行驶证等手续,让您足不出店便可拿到牌照，省时省力。 当然，不同地区，购车的手续会略有出入，要了解清楚再出手。 最后，希望你买到称心如意的车。 我买了三辆车，买一次总结一次经验，因为买车吃过亏，对奸商深恶痛绝，所以想帮你。过程不说了，只告诉你必须注意的几点: 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 1.一定要在4S店买，其他店鱼龙混杂，一旦你交了第一笔款，剩下只有被牵着鼻子走的份儿了。什么送大礼，送你防晒膜，市场上卖150，他给你算600，5000元大礼只有防晒膜、地胶和脚垫。说是包牌价，故意把购置税甩开，商业险给你按最低的上，你毫无办法，因为你不会再到他那里买第二辆车了。车出了问题由4S店修，和他一点关系也没有。只是扒你一道皮。 2.先上网查本地区的4S 店，至少找两家，上门谈但是不要急于买。如果谈包牌价必须让他把费用明细开出来，以防猫腻。稍带着找几家保险公司询一下价。 3.等4S店给你打电话，如果车型比较紧俏，挑一家你比较满意的再去一次。这一次可以提出试驾。 4.如果决定要买，先让他们列出所有费用的明细，所谓大礼包中的各项内容要列出品牌。另外一定要和他们一起去仓库提车，现在提车一般都是零公里，看过皮毛以后看轮胎，里程表是可以用电脑调的，轮胎做不了假。 5.拿到说明书按车型检查配置。 6.如果4S店有保险代理业务，并且和网上询价差不多最好一起办，因为其他保险公司都有自己的定点修车单位，不在你购车的店办，保修期内容易出现麻烦。 以上几点都把握住，你就不会吃大亏。 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed; 1.6.1 sweeping, washing preparations (1) after the pressure test is completed, before purging: purging of piping system; (2) should be made available in accordance with the owner's sweeping plan to draw sweeping system detail; (3) prepare the provisional purging, flushing tube, temporary filter, bypass or blind plate, and mark on the single line diagram; (4) ready to purge and test tools, such as: target, transparent glass. (5) the blowing and washing method: medium control norms according to the Institute's select a purging, flushing method, water steam, air purge, purge, and so on. 1.6.2 water flushing (1) rinse water should be clean water, stainless steel tubes used in the rinse water, water CL-in 25PPM; (2) water pressure should not exceed the working pressure of the pipe, using the maximum flow rate for washing; (3) providing canal irrigation should be in charge of the rinse and flush; (4) the instrument valve cannot be removed ... By-pass, wash downstream parts of the pipeline. (5) take exit of the flushing line with glasses of water, check whether the water color and transparency consistent with the entrance is qualified. After passing the line, water should be drained; (6) if the water pipes, design or party files require drying, you should dry it with compressed air. 1.6.3 air purge (1) air purge media should be no pollution and air under pressure, the pressure of sweeping shall not exceed the working pressure; (2) the competent first purge, then pipe purge; (3) devices are unlikely to participate in the purge, equipment and pipelines should be separated, and to protect the device, preventing rust, and pollutants to the top. (4) the purge should be clearly identified to prevent hurt; (5) by the owner, supervisor, principal of check purge outlet, no rust, debris, and other, confirmed the pipeline purging qualified. 1.6.4 steam purging (1) before steam blowing pressure test and insulation should be completed;