联想BIOS设置

联想BIOS设置 BIOS interface is not difficult, ah, see BOOT or BIOS, that is, set the first boot item, only a few options ah, or give you this comparison table, you look at it!! Relatively long, the patient will read, ha ha BIOS common Chinese and English comparison table Time/System Time time / system time Date/System Date date / system date Level 2 Cache two level cache System Memory system memory Video Controller video controller Panel Type LCD screen model Audio Controller audio controller Modem Controller modem (Modem) Primary Hard Drive main hard disk Modular Bay module bracket Service Tag service label Asset Tag asset labels BIOS Version BIOS version The Boot Order/Boot Sequence boot sequence (system SEARCH * as system file is pro -)? Diskette Drive floppy disk drive Internal HDD built in hard disk drive Floppy device floppy drive device Hard-Disk Drive hard disk drive USB, Storage, Device, USB storage devices CD/DVD/CD-RW Drive drive CD-ROM device drive Modular Bay HDD modular hard disk drive Cardbus NIC Cardbus bus NIC Onboard NIC onboard NIC Boot POST Boot self-test (POST) hardware check level is set to "MINIMAL" (the default) is the poweronselftest upgrade only in BIOS, memory module to change the self starting or not completed the first case of inspection. Set to "THOROUGH", then perform a full set of hardware checks when booting. Config Warnings Warning setting: this option is used to set the alarm when the system uses a lower voltage power adapter or other unsupported configuration, set to "DISABLED", disable the alarm, and set it to "ENABLED" to enable the alarm Internal Modem Built in modem: use this option to enable or disable the built-in Modem. After disabling (disabled), the Modem is not visible in the * system. LAN Controller Network controller: use this option to enable or disable the PCI Ethernet controller. After disabling, the device is not visible in the * system. PXE, BIS, Policy/PXE, BIS, Default, Policy PXE BIS policy: this option controls how the system handles without authentication (starting the overall service Boot Integrity Services (BIS)) authorization request. The system can accept or deny BIS requests. When set to "Reset", the BIS will be re initialized and set to "Deny" next time the computer is started". Onboard Bluetooth onboard Bluetooth device MiniPCI, Device, Mini, PCI devices MiniPCI Status Mini PCI device status: when you install Mini PCI devices, you can use this option to enable or disable on-board PCI devices Wireless Control Wireless control: use this option to set the control mode for MiniPCI and Bluetooth wireless devices. When set to "Application", the wireless device can be enabled or disabled by applications such as "Quickset", and the hotkey is not available. When set to "/Application", the wireless device can be enabled or disabled by applications such as "Quickset" or "hot key". When set to "Always Off", the wireless device is disabled and cannot be enabled in the * system. Wireless Wireless devices: use this option to enable or disable wireless devices. This setting can be changed via the "Quickset" or "hotkey" in * system. Whether this setting is available depends on the settings of the Wireless Control. Serial Port serial port: this option prevents device resource conflicts by redistributing port addresses or disabling ports. Infrared Data Port infrared data port. Using this setting, you can avoid device resource conflicts by redistributing port addresses or disabling ports. Parallel Mode Parallel port mode. Control of parallel computer work for the "NORMAL" (AT compatible) (standard parallel port), "BI-DIRECTIONAL" (PS/2 compatible) (bidirectional mode, allowing two-way communication host and peripherals) or "ECP" (Extended Capabilities Ports, extended port) (default). Num Lock Digital lock. Set whether the NumLock LED lights up when the system is started. Set as "DISABLE", the digital light is set to "ENABLE" and the digital light is lit when the system is started. Keyboard NumLock keyboard digital lock: this option sets whether or not to Prompt Keyboard related error messages when the system is started. Enable Keypad Enable keypad: set to BY NUMLOCK, enable the keypad when the NumLock light is on and no external keyboard is attached. Set to "Only By Key" in the NumLock light embedded keypad in a disabled state. External Hot Key External hotkey: this setting can be used on the external PS/2 keyboard in the same manner as the keys on the laptop. If you use ACPI* as a system, such as Win2000 or WinXP, the USB keyboard cannot be used. Only in pure DOS mode, can the USB keyboard use the key. Set it to "SCROLL LOCK" (default option) to enable this function and set it to "NOT INSTALLED" to disable this function. USB Emulation USB simulation: with this option, you can use the USB keyboard, USB mouse, and USB floppy disk in the system that does not support USB directly. This setting is automatically enabled during the BIOS boot process. When this function is enabled, the simulation continues to be effective when the control is transferred to the system. After disabling this function, the simulation is switched off when the control is transferred to the system. Pointing Device Pointer device: set to "SERIAL MOUSE", the external serial port, the mouse is enabled and integrated touchpad is disabled. When it is set to "PS/2 MOUSE", the integrated touchpad is disabled if the PS/2 mouse is connected externally. When set to "TOUCH PAD-PS/2 MOUSE" (default setting), if you connect to the PS/2 mouse, you can switch between the mouse and the touchpad. The change takes effect after the computer restarts. Video Expansion Video extensions: use this option to enable or disable video extensions to adjust the lower resolution to higher and normal LCD resolutions. Battery battery Battery Status battery status Power Management power management Suspend Mode suspend mode AC Power Recovery AC power recovery: this option can be reflected in the AC power adapter when the system is plugged back into the system. Low Power Mode low power mode: this option is used to set the system's battery power when it is asleep or closed. Brightness Brightness: this option sets the brightness of the display when the computer starts. The default setting is half of the computer's power supply. The default setting is maximum when the computer operates in an AC power adapter. Wakeup On LAN Network wakeup: this option setting allows the computer to be awakened from sleep when the network signal is accessed. This setting is invalid for state (Standby). The standby state can only be awakened in the * system. This setting is only valid when connected to an AC power adapter. Auto On Mod automatic boot mode: note that if the AC power adapter is not connected, this setting will not work. This option allows you to set the computer auto boot time. You can set the computer to boot automatically every day or just turn on the machine automatically on weekdays. The settings are effective after the computer restarts. Auto On Time automatic boot time: this option allows the system to automatically boot time, the time format is 24 hours. Type the value or set the value with the left and right arrow keys. The settings are effective after the computer restarts. Dock Configuration docking station configuration Docking Status docking station status Universal Connect universal interface: this setting is not valid if the system is used as a WinNT4.0 or earlier version. If more than one DELL docking device is used frequently, and the minimum time to access the docking station is minimized, set to "ENABLED" (default setting). If you want the system to be connected to the computer, each new docking station device generates a new system settings file, set to "DISABLED"". System Security system security Primary Password master password Admin Password manages passwords Hard-disk drive password (s) hard drive password Password Status Password status: this option locks the system password when the Setup password is enabled. Set this option to 'Locked' and enable the Setup password to place the system password changed. This option can also be used to place the password disabled by the user when the system is started. System Password system password Setup Password Setup password Post Hotkeys self checking hotkey: this option specifies the hotkey (F2 or F12) displayed on the screen during the boot check (POST). Chassis Intrusion Case theft: this option is used to enable or disable case theft detection features. When set to "Enable-Silent", if the chassis intrusion is detected, no warning message is sent. This option is enabled and the case cover opens, 该域将显示“检测”。 驱动器配置驱动器设置 软盘驱动器A:磁盘驱动器:如果系统中装有软驱，使用该选项可启 用或禁用软盘驱动器 主传动第一主驱动器 主要从驱动器第一从驱动器 第二主传动第二主驱动器 第二从驱动第二从驱动器 IDE硬盘的UDMA支持UDMA的IDE驱动器:使用该选项可以启用或禁用通过内部IDE DMA传输硬盘接口的。 硬盘序列硬盘驱动器顺序 系统BIOS的启动设备系统BIOS启动顺序 USB设备的USB设备 记忆的信息内存信息 存储系统系统内存:该选项显示系统中所装内存的大小及型号 系统内存速度内存速率:该选项显示所装内存的速率 内存信道模式内存信道模式:该选项显示内存槽设置。 AGP孔径AGP区域内存容量:该选项指定了分配给视频适配器的内存值。某些视频适配器可能要求多于默认值的内存量。 CPU CPU信息信息 CPU速度的CPU速率:该选项显示启动后中央处理器的运行速率 总线速度总线速率:显示处理器总线速率 0处理器ID处理器ID:显示处理器所属种类及模型号 时钟速度时钟频率 高速缓存的大小缓存值:显示处理器的二级缓存值 集成器件(legacyselect选项)集成设备 声音声音设置:使用该选项可启用或禁用音频控制器 网络接口控制器网络接口控制器:启用或禁用集成网卡 鼠标端口鼠标端口:使用该选项可启用或禁用内置PS / 2兼容鼠标控制器 USB控制器的USB控制器:使用该选项可启用或禁用板载USB控制器。 PCI插槽PCI槽:使用该选项可启用或禁用板载PCI卡槽。禁用时所有PCI插卡都不可用，并且不能被*作系统检测到。 串行端口1 串口1:使用该选项可控制内置串口的*作。设置为“自动”时，如果通过串口扩展卡在同一个端口地址上使用了两个设备，内置串口自动重新分配可用端口地址。串口先使用COM1，COM2再使用，如果两个地址都已经分配给某个端口，该端口将被禁用.. 并行端口并口:该域中可配置内置并口 模式 模式:设置为”在“时内置并口仅能输出数据到相连设备。设置为 PS / 2、EPP或ECP模式时并口可以输入、输出数据。这三种模式所 用和最大数据传输率不同。最大传输速率PS / 2 克隆软件鬼初级使用教程 One, what is Ghost? Ghost (ghost) software is a Symantec Corp in the United States launched a good hard disk backup and restore tool, can achieve FAT16, FAT32, NTFS, OS2 and a variety of hard disk partition format hard disk partition backup and restore. Commonly known as cloning software. Features: 1, now known as cloning software, the Ghost backup is based on the hard disk sector as a unit, that can be a complete physical information on the hard disk copy, rather than simply copying data; clone only clone body, but this Ghost can all Dongdong cloning of the system, including the sound animation image, even the disk fragmentation can help you copy, worse than the clone yo). Ghost supports backing up partitions or hard disks directly to a file called.Gho (Symantec calls it a mirror file) and also supports direct backups to another partition or hard disk. 2, running Ghost: so far, ghost only supports Dos running environment, this cannot be said is not a kind of regret: (. We usually copy the ghost file to start the floppy disk (U disk), it can also be recorded into the boot disk, the boot disk into the Dos environment, type ghost at the prompt, enter ghost to run, the first is on the interface Press any key to enter the ghost interface, ghost menu, the main menu consists of 4 items, from top to bottom are respectively Quit (exit), Options (Peer to, Peer (optional) point of the network, mainly used) and Local (local). Normally we only use the Local menu item, which contains three sub items: Disk (hard disk backup and restore), Partition (disk partition backup and restore), Check (hard disk detection), before the two functions we use the most, the following is the interpretation around these two expansion. 3, because the Ghost in the backup and restore is by sector to replicate, so be careful when operating, don't put the target disk (partition) has made a mistake, or will the target disk (partition) data will erase all very miserable...... There's not much chance of recovery, so be serious and careful! But you shouldn't be too nervous. In fact, Ghost is easy to use and understand the meaning of those words. You will understand its usage, plus serious attitude, you can master it! Let's get together:) Two, partition backup Prepare knowledge: recognize words Disk: No, I said, you know what the disk means; Partition: the partition in the operating system, each hard disk drive (after C) corresponds to a partition; Image: mirror image is a file format for Ghost to store hard disk or partition content. The extension is called.Gho; To: Well, in ghost, a simple understanding of to means "backup to"; From: from, in ghost, a simple understanding of "from" is "from"...... Restore. (1) brief introduction to the Partition menu There are three sub menus under it: To Partion: a partition (called source partition) is copied directly to another partition (target partition), and the target partition space must not be less than the source partition when it is being operated; To Image: backup a partition to a mirror file. Note that the partition that stores the mirrored files is no smaller than the source partition, preferably the source partition; From Image: restore the partition from the mirror file (restore the backup partition). (two) partition mirror file making 1, after running ghost, use the cursor key to move the cursor from "Local" to "Disk" and "Partition" to the "To Image" menu item, and then press enter. 2, select the local hard disk window, and then press enter. 3, select the source partition window (the source partition is the partition where you want to make it into mirror files) Use the cursor keys will be under the blue light positioning to us to produce the image file partition, press enter to confirm we have to choose the source partition, then click the Tab button to position the cursor on the OK key (the OK bond is white), and then press enter. 4, enter the image file storage directory, the default directory is stored in the ghost file directory, File name image file input file name, but also with the path of the input file name (at the same time, to ensure that the input path exists, otherwise it will prompt the illegal route), such as the input of D:\sysbak\cwin98, said it will save cwin98.gho image file to the D:\sysbak directory, lose the file name, and then press enter. 5, and then appear "whether to compress the mirror file window", there is "No (not compressed), Fast (fast compression), High (high compression ratio compression)", the compression ratio is lower, save faster. General election Fast, you can use the right cursor direction key to move to Fast, enter ok; 6, and then there is a prompt window, with cursor keys to move to "Yes", "enter" to determine. 7, Ghost starts making mirror files 8, the establishment of the mirror file, the success will appear prompted to create a successful window Enter back to the Ghost interface; 9, and then press the Q key, enter the car, you can exit ghost. At this point, the partition mirror file is finished! It's pretty simple. Three, restore the partition from the mirror file With the mirror file, we can restore it after the system crashes so that it can revert to the state of the system when it comes to making mirror files. The reduction of the mirror file is described below. (a) in the DOS state, enter the directory where Ghost, enter Ghost, enter, you can run Ghost. (two) Ghost in the main menu, use the cursor keys to move to the direction of the menu "LocalPartitionFrom Image", and then press enter. (three) "image file to restore the position of the window, in the full path and file File name input image file name (you can also use the cursor keys respectively select image file path, enter the file name, with the Tab key but difficult), such as d:\sysbak\ cwin98.gho, and then press enter. (four) appear from the mirror file, select the source partition window, and return directly. (five) again select the local hard disk window, and then enter. (six) select the target partition window from the hard disk, and we select the target partition with the cursor key (which partition will you want to restore to)?, Enter。 (seven) ask the question window, select Yes, enter OK, and ghost begin to restore the partition information. (eight) soon after the restore, the restore finished window, select Reset Computer, enter, restart the computer. Now that the partition is complete, is it fast?. Note: when selecting the target partition, be sure to choose the correct one, otherwise: (the result is the target partition, the original data will disappear.)...... Four 、 backup and restore of hard disk Sub menu of Ghost under the Disk menu can be realized directly to the hard disk copy hard disk (Disk DiskTo), to the hard disk image file (Image DiskTo), reducing disk content from the image file (Image DiskFrom). In the same computer configuration, we can first installed on a computer operating system and software, and then use the ghost hard disk copy function will complete a "copy" to other computer operating system installed, this can be much faster than the traditional method: Oh). Ghost Disk menu, the use of similar and Partition, but also not much use, in this will not go into details. Five and Ghost usage scenarios 1, the best solution: complete operating system and driver installation, software will be used (such as antivirus, media player software, office software etc.) mounted to the system tray, then install the operating system and a variety of commonly used software updates, and then optimize the system, finally you can boot to Dos do the backup disk cloning system, pay attention to the size of the disk is not less than the system disk! 2, if you neglect in a recall system installed after the backup to clone it, never mind, you'd better backup before the system disk in the junk file removal, the registry in the garbage removal (recommended by Windows, and then optimize the master) finishing system disk disk fragmentation, finishing after the completion of the Dos clone backup. 3, under what circumstances should the clone backup be restored? When you feel when the system is running slow (which is mostly due to often install uninstall software, residual or deleted some files, cause the system, system collapse disorder), compared to kill the virus, you need to restore the cloning! Sometimes, if you don't want to spend half an hour or even longer to defragment, you can also restore clone backups directly, which is much better than just defragmentation! 4, and finally stressed: in the backup restore, be sure to pay attention to select the target hard disk or partition!